Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL FOR
USE AND MAINTENANCE
Manual version: 2019-A
G
HOT AIR
GENERATORS
T R A N S L A T E D V E R S I O N F R O M I T A L I A N T O
E N G L I S H
Before installing or running the unit,
it is obligatory to carefully read and consult this manual.
Franco srl – Via Nazionale, 80 12010 Cervasca (CN), Italy
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for FRANCO G Series
Summary of Contents for FRANCO G Series
- Page 1 T R A N S L A T E D V E R S I O N F R O M I T A L I A N T O E N G L I S H Before installing or running the unit, it is obligatory to carefully read and consult this manual. Franco srl – Via Nazionale, 80 12010 Cervasca (CN), Italy...
- Page 2 FRANCO srl Manual of use and maintenance G series...
-
Page 3: Table Of Contents
FRANCO srl Manual of use and maintenance G series INDEX INDEX ............................3 1 - INTRODUCTION ......................... 4 1.1 General warnings ......................4 1.2 Instructions for proper disposal of the product ..............4 1.3 Covenants used throughout this manual ................ 5 1.4 Conservation of the instruction manual ................ -
Page 4: Introduction
This device must be used only for the functions for which it was intended "Hot air generator”. Any other use is to be considered improper and dangerous. Franco srl cannot be held liable for any damages caused by improper, incorrect or unreasonable use, or if the device is used in systems that do not comply with safety regulations. -
Page 5: Covenants Used Throughout This Manual
FRANCO srl Manual of use and maintenance G series 1.3 Covenants used throughout this manual The Manual is divided into autonomous chapters, each of which is addressed to a specific operator’s figure (installer, operator and maintainer), for which the skills needed to operate the machine safely have been defined. -
Page 6: Recipients
FRANCO srl Manual of use and maintenance G series 1.5 Recipients The manual is addressed to: the installer, the operator, and the qualified personnel entitled to the maintenance of the device. EXPOSED PERSON: refers to any person exposed, wholly or partially, to a danger zone;... - Page 7 FRANCO srl Manual of use and maintenance G series OTHER DEFINITIONS: HUMAN-MACHINE INTERACTION: Any situation in which an operator interacts with the machine in any of the operational phases at any time of the life of the machine itself; OPERATOR’S QUALIFICATION: Minimum level of competence that an operator must have in order to perform the described operation;...
- Page 8 FRANCO srl Manual of use and maintenance G series PICTOGRAPHS CONCERNING THE OPERATOR’S QUALIFICATION Symbol Description Generic laborer: operator lacking of specific competences, capable of performing only simple tasks under the control of qualified technicians. Lifting and handling vehicles driver: operator qualified for the use of vehicles used in lifting and handling materials and machines (carefully following the manufacturer’s instructions), in accordance...
- Page 9 FRANCO srl Manual of use and maintenance G series PICTOGRAPHS CONCERNING SAFETY The pictograms contained in a triangle indicate DANGER. The pictograms contained in a circle impose PROHIBITION / OBLIGATION. Pictograph Denomination Hazardous voltage. Entanglement. Dragging. General danger. Do not remove safety devices.
-
Page 10: Applications
1.7 Applications The G series series hot air generators run on LPG (Liquid petroleum gas) and methane as the combustion fuel. The G series generators are of direct combustion type. The air is heated by means of the thermal energy generated during combustion and is transferred to the environment to be heated with the combustion products, thereby rendering the thermal energy produced 100% available. -
Page 11: Parts Description
Verify the integrity of the machine by controlling that there are no visible damaged parts. Do not dispose the packaging elements in the environment; they must be placed in proper collection points. G series generator can be lifted and hung by using the proper brackets. WARNING! Before handling the device: a. -
Page 12: Warranty
Franco s.r.l. from Cervasca (CN), Italy. During the warranty period, the company Franco s.r.l. commits itself to replace or repair free of charge those parts which result faulty from the origin. -
Page 13: Declaration Of Conformity
FRANCO srl Manual of use and maintenance G series 1.15 Declaration of conformity (All. IIa DIR. 2006/42/CE) FRANCO S.r.l. Company Via Nazionale, 80 12010 Address Postal code Province Cervasca Italy City Country DECLARE THAT THE MACHINE G36-25; G45-40; G56-65; G56-90... -
Page 14: Installation
2 - INSTALLATION 2.1 Before installing In order to start the hot air generator G series, the following conditions are required: • connection to the electric power supply with voltage and frequency suitable for the machine and with grounding and safety devices;... -
Page 15: Electrical Connection
The installation must foresee a device enabled to disconnect the machine from the electric supply. 2.4 Gas supply connection The G series generator comes complete with gas valve inside the machine’s electrical box. The plug for the line connection is 1/2”. -
Page 16: Start And Stop
FRANCO srl Manual of use and maintenance G series 3.3 Start and stop The machine starts when the consent is given on the thermostatic socket contacts (see diagram sez.5.3) or, if the thermostat was not used, when the electrical supply is connected to the fan and to the generator. -
Page 17: Replacement Or Cleaning Of The Nozzle
FRANCO srl Manual of use and maintenance G series 4.2 Replacement or cleaning of the nozzle After making sure that the machine is stopped and cold, disconnect the electrical and gas supplies. Remove with a hex wrench #7, the 4 screws holding the safety net on the generator’s aspiration inlet. -
Page 18: Wiring
FRANCO srl Manual of use and maintenance G series 5.2 Wiring All the wires used must be suitable to carry the current intensity (A) of the motor (par. 5.1). Terminal’s screws must be accurately tightened. Make sure that the electricity supply characteristics are exactly as shown in the table (par. 5.1). -
Page 19: Wiring Diagram G56-65 - G56-90
5.4 WIRING DIAGRAM G56-65 – G56-90 5.5 THERMOSTATIC SOCKET USAGE G series hot air generators are provided of a thermostatic socket to control the ignition of the appliance. The special cap (when inserted), enables the ignition of the generator. Is it possible to start the ignition from remote, by closing a contact between pin 1 and 2 of the provided plug (e.g. -
Page 20: Spare Parts
FRANCO srl Manual of use and maintenance G series 5.6 Spare parts It is highly recommended to use only original spare parts. Orders must be made by specifying what follows: - Device model - Reference of the piece (as indicated as follows) - Page 21 FRANCO srl Manual of use and maintenance G series G56-65 G56-90 Pos. Q.tà Descrizione cod. cod. 1401006 1401006 PROTECTION GRID 1203004 1203004 PROTECTION GRID FIXING KIT 1453500 1453500 BURNER COMPLETE WITH DISK 1403005 1403005 BURNER FIXING KIT 7302003 7302003 ELECTRODES...
- Page 22 FRANCO srl Manual of use and maintenance G series ELECTRIC BOX – EXPLODED VIEW Item G36-25 G45-40 G56-65 G56-90 Qty. Description 1451005 1452005 1453005 1453005 Electric box bracket 7303000 7303000 7303000 7303000 Security thermostat 1451002 1453002 1453002 1453002 Thermostat bulb bracket...
-
Page 23: Problems And Solutions
FRANCO srl Manual of use and maintenance G series 6 – PROBLEMS AND SOLUTIONS Before undertaking any maintenance, disconnect the device from the electricity and gas supply! Problem Cause Solution Verify the electrical connection, or the functioning of the The power supply is not plugged. - Page 24 FRANCO srl Manual of use and maintenance G series FRANCO s.r.l. Headquarters and plant: Via Nazionale n.80 - 12010 - CERVASCA (CUNEO) Italy Tel. (+39) 0171 611663 – Fax (+39) 0171 612337 www.francosrl.com info@francosrl.com For further information, requests or suggestions, please contact us at:...
Need help?
Do you have a question about the G Series and is the answer not in the manual?
Questions and answers