1. Manuals
  2. Brands
  3. SilentWind Manuals
  4. Wind Turbines
  5. Hybrid 600
  6. Troubleshooting manual

SilentWind Hybrid 600 Troubleshooting Manual

Low power problem
Hide thumbs
Table of Contents

Advertisement

Quick Links

Troubleshooting
Low power problem
V28_03_2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hybrid 600 and is the answer not in the manual?

Questions and answers

Related Manuals for SilentWind Hybrid 600

Summary of Contents for SilentWind Hybrid 600

  • Page 1 Troubleshooting Low power problem V28_03_2019...
  • Page 2 Troubleshooting_Low_Power_v28_03_2019 Download section at: https://www.silentwindgenerator.com/en/download/...

  • Page 3: Table Of Contents

    Index Tables ................................. 4 Device settings on Hybrid 600 ......................4 Device settings on Hybrid 1000 ......................4 Device settings Hybrid Boost PWM version ..................4 Device settings Hybrid Boost MPPT version..................5 Resistance winding values ........................5 How to measure the resistance on the AC cables ..................6 Recommended check sequence ........................

  • Page 4: Tables

    1. Tables 1.1 Device settings on Hybrid 600 Values Charge off 14,4V 28,8V Breake on 27 - 29A Break time 50 s 1.2 Device settings on Hybrid 1000 Values Charge off 14,4V 28,8V Brake on 27A - 29A 1.3 Device settings Hybrid Boost PWM version...

  • Page 5: Device Settings Hybrid Boost Mppt Version

    1.4 Device settings Hybrid Boost MPPT version Values End of charge voltage 14,4V 28,8V 57,6V Overvoltage Low Wind Boost Storm Brake Under Voltage Switch off 10,8V 21,6V 43,2V Under Voltage Recovery On Solar Switch off 1,5V Solar Switch on 1.5 Resistance winding values Values Version Hybrid 1000...

  • Page 6: How To Measure The Resistance On The Ac Cables

    Remove the AC cables from the controller to perform the measurements. If the measurements are out-of-range, go to next step. If the measurement values are correct, you might have a damaged controller. Please contact Silentwind. Troubleshooting_Low_Power_v28_03_2019 Download section at: https://www.silentwindgenerator.com/en/download/...

  • Page 7: At The Wind Generator Ac Wires

    2.2 At the wind generator AC wires Measure here Measure directly in the Silentwind wind generator wires. The values are described at 1.5 table. If the measurements are in range, it means that the extension cables are faulty and should be repaired/replaced.
  • Page 8 3.3.2. Unscrew the 3 screws on the front plate (please be careful not to damage the front face paint). The front face should go out easily. 3.3.3. Unscrew the wires that are connected to the PCB and perform the measurements (you don’t need to completely remove the windings).

  • Page 9: How To Remove The Wind Generator Windings

    3. How to remove the wind generator windings Remove the 3 front face screws. Be careful not to chip the front face paint. The front face can be easily removed. Unscrew the three marked screws and the font face set can be removed from the body. Troubleshooting_Low_Power_v28_03_2019 Download section at: https://www.silentwindgenerator.com/en/download/...
  • Page 10 Removing the rotor, it’s not difficult but it can be a bit tricky. Please be careful not to harm yourself neither the equipment. To remove the rotor, you can press the axis against a table to go half way then pull it out completely. The windings are usually sold with the front face but if you pretend to completely remove the stator, you must use a rubber hammer and hit the front face to be able to release it.

  • Page 11: How To Clean The Slip Ring

    4. How to clean the Slip Ring To be able to clean the Slip Ring, please read the previous chapter How to remove the wind generator winding to disassemble the front face. To remove the Slip Ring, you must first remove the PCB. Disconnect the three AC wires, unscrew the three screws (A) and disconnect them from the PCB.
  • Page 12 Remove the marked Slip Ring screws. The Brushes have a compression spring. Please be careful when removing the Brushes. You don’t need to remove the other two screws to perform the Slip Ring cleaning. The Slip Ring Exploded view. Troubleshooting_Low_Power_v28_03_2019 Download section at: https://www.silentwindgenerator.com/en/download/...
  • Page 13 CLEAN HERE! First, clean the marked contacts with a clean cloth (see the above drawing). If the surfaces are not clean enough, use the cloth with a bit of Alcohol. Using Isopropyl Alcohol (Isopropanol) is more efficient but the standard Ethyl Alcohol 96% can also be used. The last resort will be using a high grit sand paper (600 grit up).
  • Page 14 To assemble the Slip Ring, do it in reverse order. 1-2-3 After assembling the Slip ring and before assembling it on the wind generator body, please confirm the wire resistance with the multimeter. Measure from 1 to 1, 2 to 2 and 3 to 3, it should act like a short-cut and it should not have any resistance. If you are measuring 2 Ω...

  • Page 15: Silentwind Help Request Contact

    The Wind Generator version, the controller’s serial number (or model ID), the battery set (Gel, AGM, the Voltage, …), if you are using PV panels, when you bought the equipment (to check the warranty), Smartphone or tablet OS version, Silentwind APP version, … Description: A short problem description and any relevant information that can help to identify the root/cause.

This manual is also suitable for:

Hybrid 1000Hybrid boost pwmHybrid boost mppt

Table of Contents