Yaesu SCU-LAN10 Installation Manual

Yaesu SCU-LAN10 Installation Manual

Network remote control system
Hide thumbs Also See for SCU-LAN10:

Advertisement

Network Remote Control System
SCU-LAN10
Installation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCU-LAN10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Yaesu SCU-LAN10

  • Page 1 Network Remote Control System SCU-LAN10 Installation Manual...
  • Page 2: Preparation Procedure

    Commercially available straight Ethernet cable (category 5e or higher) z PC Software Download the “SCU-LAN10 Remote Software” and “SCU-LAN10 Setting Tool” from our website. Initial settings for SCU-LAN10 and remote control software are required. These initial settings are required only once at the first time.
  • Page 3: Table Of Contents

    Install the SCU-LAN10 and FTDX101MP/D ............... 31 Initial settings for remote control software .............. 33 About setting items ....................34 Initial audio level settings ..................35 Windows volume control ..................35 Volume control of SCU-LAN10 Network Remote Control Software ......39 Start remote control ....................40...
  • Page 4: Introduction

    PC and peripheral devices. • To use SCU-LAN10, you need to open the port of the router and change the settings of the firewall and se- curity software. Customers are responsible for network security when using this product.
  • Page 5: System Requirements (Operating Environment)

    System Requirements (Operating Environment) z Supported Transceivers FTDX101MP, FTDX101D (As of April 2020) z The latest Transceiver Firmware Update to the latest software and firmware on the YAESU website (https://www.yaesu.com). • FTDX101MP/D MAIN: V01-14 or later DISPLAY: V01-06 or later...
  • Page 6: Other Notes And Restrictions

    • CW mode reception is supported, but remote station operation in CW mode is not possible. • Transceiver power ON / OFF is not available. Packing List • SCU-LAN10 unit • Connection Cable (13pin DIN plug) • USB A-B Cable •...
  • Page 7: Scu-Lan10

    In addition to the POWER indicator, various statuses of this unit are displayed. When main power is supplied to the transceiver, the SCU-LAN10 will start up and enter the standby state. The STATUS indicator (red) starts blinking ∙∙∙∙∙∙ SCU-LAN10 start up POWER indicator (green) blinks (after about 12 seconds) ∙∙∙∙∙∙...
  • Page 8: Check The Lan For Installing The Transceiver

    Example: 255.255.255.0, 255.255.0.0, etc. „ IP addresses of other devices (other computers, network cameras, etc.) connected to the same router* If there is a device with the same IP address as SCU-LAN10 in the same network, it will not operate normally.
  • Page 9 ( 2 ) When connecting directly with an Ethernet cable for remote control If you connect the FTDX101MP/D and the SCU-LAN10 directly with an Ethernet cable without using a router in the same building, you do not need to check the network environment.
  • Page 10: Install The Software On A Computer

    Install the software on a computer  Install the software on the computer that will be used for initial setup and remote control. This step is not necessary if you have already installed the software.  Install Microsoft .NET Framework 4.X Operations on a Windows 10 computer are shown in the procedure below for the purpose of explanation.
  • Page 11: Install The Network Remote Control Software

    Install the Network Remote Control Software Execute the installer and install the “SCU-LAN10 Network Remote Control Software” and “SCU-LAN10 Setting Tool” on the PC. Unzip the zip file (SCU-LAN10_Software_V****.zip) downloaded from YAESU website. The destination folder will be opened automatically.
  • Page 12 When the installation is complete, “Congratulations!” Will be displayed. 6. Click [Finish]. Installation of “SCU-LAN10 Network Remote Control Software” and “SCU-LAN10 Setting Software” is completed. If the computer used for the initial settings of SUC-LAN10 and the computer used for remote control are different, install the...
  • Page 13: Preparation For Initial Setting

    For initial setting, refer to the figure and connect the PC and the SCU-LAN10 directly with a commercially available straight Ethernet cable. z It is recommended to connect the PC and SCU-LAN10 directly with an Ethernet cable as shown in the figure without using a router for the initial setting.
  • Page 14: Temporarily Change The Pc Network Settings

    Temporarily change the PC network settings It is necessary to temporarily change the network settings of the PC that is connected to SCU-LAN10 and used for the initial settings. When you change the network settings, you may not be able to connect to the Internet or network devices from your com- puter, so restore the settings at the end of this procedure.
  • Page 15 3. Double-click the network adapter (LAN card) connected to SCU-LAN10. The “Ethernet status” screen is displayed. 4. Click [Properties].
  • Page 16 5. Click [Internet Protocol Version 4 (TCP/IPv4)], and then click [Properties]. “Internet Protocol Version 4 (TCP/IPv4) Properties” screen appears. Please note that “Internet Protocol Version 6 (TCP/IPv6)” cannot be used.  6. Make a note of all the settings below before making any changes to restore the network settings after completing the settings.
  • Page 17 It is automatically changed to “Use the following DNS server addresses”. No DNS server settings are required. Enter “192.168.49.10” Enter “255.255.255.0” Leave the blank 8. Click [OK]. 9. Close unnecessary Windows screens. The network settings of the PC for initial setting of SCU-LAN10 is completed.
  • Page 18: X84; Setting The Scu-Lan10

    SCU-LAN10 by ping (pin) command” (Page 19). To reset the SCU-LAN10. Press and hold the [RESET] button on the front panel of the SCU-LAN10 with the thin-tipped bar for about 5 seconds until only the STATUS indicator (red) blinks. Please note that resetting will restore the SCU-...
  • Page 19 (2) Scroll the Start menu and click the “Windows System” group. (3) Click [Command Prompt]. The “Command Prompt” screen is displayed. (4) Enter “ping 192.168.49.1” (for SCU-LAN10 set at the factory) and press the Enter key. “Replay from 192.168.49.1:” is displayed, network communication is normal. If “Replay from 192.168.49.1:” is not displayed, refer to “...
  • Page 20 8. Set it according to the network environment of the place where SCU-LAN10 and the transceiver are ac- tually installed, which was confirmed in “ Check the LAN for installing the transceiver” (Page 8) The following three connection examples are explained, so please refer to the diagram that applies to your installation.
  • Page 21 (4) Go to step 9 on the next page (2) When connecting directly with a LAN cable for remote control Remote control PC SCU-LAN10 (1) Setting an “IP Address” Set an IP address other than the computer's IP address. Generally, set as follows.
  • Page 22 ( 3 ) Remote control within the same LAN using a router  IP address Other network device Remote control PC Router SCU-LAN10  IP address of the router  Subnet mask Set according to the following network environment confirmed in “...
  • Page 23: Other Functions Of Scu-Lan10 Setting Tool

    At this time, if the setting environment and the actually used network environment are different, the con- nection between the setting software and SCU-LAN10 will be disconnected, but this is normal. 12. Click [Close] at the top right of the screen to close the screen.
  • Page 24 The new password will be saved. ● F/W Update screen When the firmware of SCU-LAN10 is updated, the firmware will be downloaded from YAESU website and updated. Updates can be done remotely via the Internet or LAN. For details on the update operation, refer to the update manual attached to the SCU-LAN10 firmware.
  • Page 25: Restore The Network Settings Of The Computer

    Restore the network settings of the computer  After completing the initial settings of SCU-LAN10, restore the network settings of the personal computer. If you do not restore the settings, you may not be able to connect to the Internet or network devices from your computer.
  • Page 26 3. Double-click the network adapter (LAN card) to which SCU-LAN10 is connected. The “Ethernet status” screen is displayed. 4. Click [Properties].
  • Page 27 5. Click [Internet Protocol Version 4 (TCP/IPv4)], and then click [Properties]. “Internet Protocol Version 4 (TCP/IPv4) Properties” screen appears. 6. Set the LAN environment as it was in step 6 of “Temporarily change the PC network settings” (Page 14)before the change. If it was set to “Obtain DNS server address automatically (B)”...
  • Page 28: Initial Setting Of Ftdx101Mp/D

    Initial setting of FTDX101MP/D  Set the FTDX101MP/D in advance as follows for remote control. All the following settings are required for nor- mal remote control. Please refer to “FTDX101MP/D setting menu operation procedure” (Next page) for the setting operation of FTDX101MP/D. Settings for transmit audio Change the transmit audio setting for each mode to SOURCE: REAR, REAR SELECT: USB.
  • Page 29 ● FTDX101MP/D setting menu operation procedure 1. Press the [FUNC] key. 2. Touch the category item you want to set. Or turn the [MULTI] knob to select a category item and press the [MULTI] knob. Comprehensive settings such as: Transmit & Receive, Interference Reduction, Memory, Scan, etc.
  • Page 30: Open Udp Port Of Router

    Open UDP port of router  When using a router or firewall in the LAN environment where the transceiver and SCU-LAN10 are installed, it is necessary to open the UDP (User Datagram Protocol) port (permit communication). By default, the following 4 UDP ports are used.
  • Page 31: Remote Connection

    1. Turn the transceiver OFF. 2. Connect the SCU-LAN10 to a router or computer with a commercially available straight LAN cable. 3. Connect the SCU-LAN10 and FTDX101MP/D with the included ACC cable and USB cable. Attach the two included ferrite cores to the bases of the connectors on both ends of the ACC cable using ...
  • Page 32 ACC cable. EXT SPKR METER EXT ALC RS-232C ANT 1 ANT 2 LINEAR +13.8V TUNER 1. Turn the transceiver ON. Confirm that only the POWER indicator (green) of SCU-LAN10 is in the state of blinking. (It takes about 12 seconds.)
  • Page 33: Initial Settings For Remote Control Software

    Initial settings for remote control software Start the remote control software “SCU-LAN10 Network Remote Control Software”. 1. Click the Windows Start button, and then click the [YAESU SCU-LAN10] icon in the “Yaesu Musen” group to start the remote control software.
  • Page 34: About Setting Items

    Password: Enter the password that is set for SCU-LAN10. (2) Network settings Remote Address: Enter the remote address to connect to SCU-LAN10. The settings differ depending on the network environment as follows: When using the Internet For fixed global IP: Enter the fixed IP address obtained from the provider...
  • Page 35: Initial Audio Level Settings

    Initial audio level settings Make the initial settings for levels of the transmitted audio and received audio. Make settings on the Windows system and fine-tune on the screen of the remote control software during op- eration. Windows volume control 1. Click [Setup], and then click [Audio Setup]. The “Audio Setup”...
  • Page 36 4. Click the [Level] tab. 5. Drag the [Slide Bar] to adjust the volume and then click [OK]. This volume level is the system master volume. You cannot hear the received sound if it is muted or is zero.  6.
  • Page 37 7. Click the [Recording device] that is connected to the microphone, and then click [Properties]. The “Properties” screen of the recording device is displayed. 8. Click the [Level] tab. 9. Drag the [Slide Bar] to adjust the microphone volume, then click [OK]. If it is muted (no sound) or set to zero, the transceiver cannot be modulated from the microphone of the ...
  • Page 38 10. Click [OK] on the Windows “Sound” screen. 11. On the “Audio Setup” screen, click “Open System Mixer”. The Windows “Volume Mixer” screen appears. 12. Drag the “SCN-LAN10 Remote Control Software” [slide bar] to adjust the speaker volume. 13. Click the [X] at the top right of the screen to close the screen.
  • Page 39: Volume Control Of Scu-Lan10 Network Remote Control Software

    Volume control of SCU-LAN10 Network Remote Control Software 1. Adjust the volume on the “Audio Setup” screen. If the “Audio Setup” screen is not open, click [Setup] and then [Audio Setup]. TX AUDIO Adjust the transmit modulation level. This adjustment is the same as the MIC GAIN adjustment bar that appears when you right-click the MIC GAIN/PROC button.
  • Page 40: Start Remote Control

    Click the warning sign to see the detected issues. Refer to the Remote Control Unit SCU-LAN10 Operation Manual for details on remote control operation. The operation manual can be opened by clicking “Operation Manual (English)” from the Help menu of the remote control software.
  • Page 41 Copyright 2020 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.

Table of Contents

Save PDF