Sealey SC10.V2 Instructions

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. CONTENTS
Section 2. General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
Section 2.1 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
Section 2.2. Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.
Section 3. Safety/Operational Instructions. . . . . . . . . . . . . . . . . . .2.
Section 4. Maintenance/Examination/Inspection. . . . . . . . . . . . . .2.
Section 5. Assembly and storage. . . . . . . . . . . . . . . . . . . . . . . . . .3.
Section 6. Owner's & Operator's Responsibilities . . . . . . . . . . . . .3.
Section 7. Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . .4.
Section 8. Parts List/Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.
2. GENERAL
2.1 Identification
Supplier: Sealey Power Products,
Kempson Way,
Suffolk Business Park,
Bury St Edmunds,
Suffolk, IP32 7AR.
Model No: SC10.V2
2.2 Technical Data
Rated Capacity
Safe Working Load (SWL) 10t (tested to 50% overload).
Working Load Limit (WLL) 10t (tested to 50% overload).
Lifting Cap. in Position 1: . . . . . . . . . . . . . . 1000kg
Lifting Cap. in Position 2: . . . . . . . . . . . . . . 750kg
Lifting Cap. in Position 3: . . . . . . . . . . . . . . 500kg
Lifting Cap. in Position 4: . . . . . . . . . . . . . . 250kg
Maximum Lift Ht. at Minimum Jib Extn: . . . 1855mm
Maximum Lift Ht. at Maximum Jib Extn: . . . 1990mm
Length of Jib Position 1: . . . . . . . . . . . . . . . 893mm
Length of Jib Position 2: . . . . . . . . . . . . . . . 983mm
Length of Jib Position 3: . . . . . . . . . . . . . . . 1073mm
Length of Jib Position 4: . . . . . . . . . . . . . . . 1163mm
a) Design Capability: Test Load 50% overload.
b) For a description of in-service and out-of-service conditions see
section 3 Safety, Section 4 Maintenance and Section 6.
c) The crane is fitted with a bypass valve that will prevent the ram
from over extending.
d) For applications see Section 3 Safety.
e) For control system, see Fig.1 for release valve and pump handle
assy. Usage is explained in Section 3.2 Operation.
f) For ground condition requirements, see Section 3 Safety.
g) For information on parts and materials requiring specialised
repair techniques see Section 4 Maintenance.
Instructions for:
FOLDING WORKSHOP CRANE
Model No:
Page No.
Height of Frame:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147mm
Length of Frame: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1518mm
Overall Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1550mm
Maximum Width of Frame: . . . . . . . . . . . . . . . . . . . . . . . . .962mm
Width Inside Frame: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .862mm
Distance between Centres of Rear Wheels: . . . . . . . . . . . 685mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74kg
fig.1
PUMP HANDLE ASSY.
PAGE 1
SC10.V2
500kg Max.
750kg Max.
1000kg Max.
1518mm
RELEASE VALVE
250kg Max.
SC10.V2 - 1 - 011007