Table of Contents
Advertisement
INSTALLATION & OPERATION MANUAL FOR
ITW Food Equipment Group, LLC
An Illinois Tool Works Company
701 South Ridge Avenue, Troy, OH 45374
Heavy Duty Gas Griddles
MODELS
AGM24
AGM36
AGM48
AGM60
AGM72
AGT24
AGT36
AGT48
AGT60
AGT72
MLS
ML-135236-AGM24
ML-135237-AGM36
ML-135238-AGM48
ML-135239-AGM60
ML-135240-AGM72
ML-135231-AGT24
ML-135232-AGT36
ML-135233-AGT48
ML-135234-AGT60
ML-135235-AGT72
www.wolfrange.com
FORM F-36959 (6-06)
Advertisement
Table of Contents
Related Manuals for Wolf AGM24
Summary of Contents for Wolf AGM24
- Page 1 INSTALLATION & OPERATION MANUAL FOR Heavy Duty Gas Griddles ITW Food Equipment Group, LLC An Illinois Tool Works Company 701 South Ridge Avenue, Troy, OH 45374 MODELS AGM24 ML-135236-AGM24 AGM36 ML-135237-AGM36 AGM48 ML-135238-AGM48 AGM60 ML-135239-AGM60 AGM72 ML-135240-AGM72 AGT24 ML-135231-AGT24 AGT36...
-
Page 2: Important For Your Safety
IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. -
Page 3: Installation
Heavy Duty Gas Griddles are produced with quality workmanship and materials. Proper installation, usage and maintenance of your griddle will result in many years of satisfactory performance. Thoroughly read this entire manual and carefully follow all of the instructions provided Model AGM24, AGT24 AGM36, AGT36 AGM48, AGT48 AGM60, AGT60 AGM72, AGT72 Before installing, verify that the and type of gas supply (natural gas or propane) agree with the specifications on the rating plate located inside the griddle front panel. -
Page 4: Installation Clearances
LOCATION The installation location must be kept free and clear of combustibles. When installing, never enclose the bottom of the griddle with a raised curb or other constructions that would obstruct flow of air into or out of the griddle. Adequate clearance for air openings into the combustion chamber must be provided. -
Page 5: Cutting Boards
GRIDDLES MOUNTED ON STANDS WITH CASTERS Griddles mounted on stands with casters must use a flexible connector (not supplied) that complies with the Standard for Connectors for Movable Gas Appliances ANSI Z21.69•CSA6.16, and a quick-disconnect device that complies with Gas Fuel, ANSI Z21.3•CSA6.9. In addition, adequate means must be provided to limit movement of the appliance without depending on the connector and the quick-disconnect device (or its... -
Page 6: Gas Pressure Regulator Installation
GAS PRESSURE REGULATOR INSTALLATION Gas regulator pressure is preset at 5” Water Column (W.C.) for natural gas, and 10” W.C. for propane gas. No further adjustment should be required. Install the regulator as close to the griddle on the gas supply line as possible. Make sure that the arrow on the underside of the regulator is oriented in the direction of gas flow to the griddle (Fig. -
Page 7: Operation
OPERATION WARNING: THE GRIDDLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING. BEFORE FIRST USE The griddle is shipped covered with a protective coating. Remove this film only when the griddle plate is being cleaned prior to its first cooking use. Use a non-corrosive, grease dissolving commercial cleaner, following the manufacturer’s directions. -
Page 8: Using The Griddle
USING THE GRIDDLE To preheat, turn the burners on about 20-25 minutes before cooking. A uniform and systematic approach to loading the griddle will produce the most consistent product results. The griddle plate is steel, but the surface is relatively soft and can be scored or dented by careless use of a spatula or scraper. - Page 9 CLEANING THE GRIDDLE Empty the grease drawer as needed throughout the day and regularly clean at least once daily. Clean the griddle regularly. A clean griddle always looks better, lasts longer and performs better. To produce evenly cooked, perfectly browned griddle products keep the griddle plate clean and free of carbonized grease.
-
Page 10: Pilot Adjustment
LEVELING 1. Place a level on the griddle. 2. Adjust legs by turning the bullet feet at the bottom of each leg. Using pliers or a crescent wrench, turn the feet counter-clockwise to increase height, and clockwise to decrease height until leveling is achieved. Do not extend the legs more than 1-¾”. CALIBRATION (AGT Models only) 1. -
Page 11: Maintenance
MAINTENANCE WARNING: THE GRIDDLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE GRIDDLE. LUBRICATION All valves and thermostats must be checked and lubricated periodically. Check with your Service Agency for details. VENT Annually, when the griddle is cool, check the flue and clear any obstructions. SERVICE AND PARTS INFORMATION Contact the Service Agency in your area to obtain service and parts information. -
Page 12: Troubleshooting
PROBLEM Heat does not come on when the thermostat is turned on Pilot burner will not light Pilot burner will not stay Fat appears to smoke excessively Food sticks to griddle or burned around edges or contains dark specs Food under-cooked inside Food tastes greasy or has objectionable off-flavor Noticeable build-up of...
Need help?
Do you have a question about the AGM24 and is the answer not in the manual?
Questions and answers