TDE MACNO DSV Series Quick Start

PROGRAMMING KEY: Operating instructions
Transferring parameters from the key to the inverter:
- Remove the key connector cover and insert the key.
- From the keyboard select parameter C - 040, select do then press E.
The "done " message is displayed for 2 seconds to confirm that the operation has
terminated successfully.
List of main parameters (see the manual for the complete list) :
Parameter display menu.
D - DISPLAY menu
Code Description
d-000 d-000 d-000 d-000 d-000 Output frequency (0.1 Hz)
d-001 d-001 d-001 d-001 d-001 Reference frequency (0.1 Hz)
d-002 d-002 d-002 d-002 d-002 Output current (rms) (0.1 A)
d-003 d-003 d-003 d-003 d-003 Output voltage (rms) (1 V)
Basic drive start-up menu.
S - START-UP menu
P
ARA
Description
METER
Mains voltage (V)
S-000 S-000 S-000 S-000 S-000
Mains frequency (Hz)
S-001 S-001 S-001
S-001 S-001
S-100 S-100 Maximum output voltage (V)
S-100 S-100 S-100
Base frequency (Hz)
S-101 S-101 S-101 S-101 S-101
Nominal motor current
S-150 S-150 S-150 S-150 S-150
Pairs of motor poles
S-151 S-151 S-151 S-151 S-151
Plated motor cos value
S-152 S-152 S-152 S-152 S-152 Ö
Motor stator resistance (ohm)
S-153 S-153 S-153 S-153 S-153
START & STOP command source (1= terminals)
S-200 S-200 S-200
S-200 S-200
Maximum analog reference frequency
S-201 S-201 S-201 S-201 S-201
Reference channel source (1=AN IN1 +/-10V) (2=AN IN2 +/-10V)
S-202 S-202 S-202 S-202 S-202
Digital reference frequency
S-203 S-203 S-203 S-203 S-203
S-300 S-300 S-300 S-300 S-300 MOT-1 ramp-up time
S-301 S-301 S-301 S-301 S-301 MOT-1 ramp-down time
S-400 S-400 S-400 Manual boost
S-400 S-400
S-401 S-401
S-401 S-401 S-401 Automatic boost on/off ( 1=on)
S-450 S-450 S-450 S-450 S-450 Slip compensation
S-451 S-451 S-451 S-451 S-451 Compensation time constant
S-900 S-900 S-900 S-900 S-900 Stator resistance measure command
S-901 S-901 S-901 S-901 S-901 Parameter save command
Drive digital/analog input/output settings menu.
I - INTERFACE menu
P
ARAMETER
Description
I-000 I-000 I-000 I-000 I-000 a I-007 I-007
Configure inputs IN1 to IN8
I-100 I-100 I-100 I-100 I-100 a I-103 I-103 I-103 I-103 I-103
Configure outputs OUT 1 - OUT 2 - RLA - RLB
I-200 I-200 I-200 I-200 I-200
Configure input AN1 terminal 23 (default = 0 +/-10V)
I-210 I-210 I-210
I-210 I-210
Configure input AN2 terminal 11-12 (default = 0 +/-10V)
I-300 I-300 I-300 I-300 I-300
Configure analog output 1 terminal 21 (default = 0 Freq. out)
Multi-speed and ramp settings menu.
F - FREQ& RAMP menu
Code
Description
f-100 f-100 f-100 f-100 f-100 /f-115 f-115 f-115 Digital frequencies
f-116 Jogging frequencies
Drive functioning parameter settings menu.
P - PARAMETER menu
Code Description
P-001 P-001 P-001 P-001 P-001
1 = Reverse enabled without start command
P-002 P-002 P-002 P-002 P-002
1 = Reverse enabled
A - APPLICA TION menu
C - COMMAND menu
Code Action performed
C-000 C-000 C-000 C-000 C-000 Parameter save
C-001 C-001 C-001 Load previously stored parameters
C-001 C-001
Load default parameters
C-002 C-002 C-002 C-002 C-002
C-020 C-020 C-020 C-020 C-020 Reset alarm memory
C-040 C-040 C-040 C-040 C-040 Load and save parameters from external programming key
[from key to Inv.]
(unit of measure)
C-041 C-041 C-041 C-041 C-041 Save inverter parameters in external programming key
[from Inv. to key]
C-100 C-100
C-100 C-100 C-100 Measure motor phase resistance and initialise parameter
Configuring the programmable digital inputs (IN1..IN8) with: I-000 ... I-007.
Value Name
0 None
Run
1
2 Reverse
3 EF NO
4 EF NC
5 Al res
Freq.Sel 1
7
8 Freq. Sel2
Digital (OUT1, OUT2) I-100, I-101;relay outputs (RLA, RLB) I-102, I-103
Value Event signalled by digital output (output on)
Inverter ready status
0
1 Inverter alarm status
2 Inverter not in alarm status(negative logic)
3 Motor running
4 Motor not running
5 Anti-clockwise rotation (output off otherwise)
Inverter at full speed (end of ramp-up)
6
7 Ramping up or down.
12 Generic drive limit signal
29 Output frequency = programmed frequency P-440 & P-441
30 Output frequency = programmed frequency P-440 & P-441
31 Output frequency > programmed frequency P-440 & P-441
32 Output frequency < programmed frequency P-440 & P-441
Open collector outputs OUT1 and OUT2 (terminals 19 and 20) are configured by
parameters I-100 for OUT1 and I-101 for OUT2.
Relay output RLA (terminals A1, A2, A3) is programmed with I-102.
Alarms
E
VENT SIGNALLED
External
Overcurrent
Overvoltage
Undervoltage
Overtemperature
Inverter overload
Motor overload
PID functioning settings menu.
Control functions menu (Save parameters, Load defaults,
Autocalibrate, etc.).
S-153
Action performed
Not used
RUN (START) command
REVERSE command
External fault with NO contacts
External fault with NC contacts
Alarm reset command
Freq. selector 1
Freq. selector 2
E
DISPLAY VENT SIGNALLED
EF Resistance overload
OC Overtorque
OU Missing input phase
UU Not used
OH EEPROM error
OLI Configuration error
OLN Program error
DSV
SERIES
Introduction
The Serie V inverters allow an efficient and flexible
control of motor speed. In this way, the asynchronous
motor can be used in a wider range of applications.
The functioning interface is made of a panel consisting
of six keys, one display with five 7-segment digits and
seven leds.
The display and the keys allow you to change all the
inverter parameters so as to make it suitable to all
applications.
The drive display allows the monitoring of controlled
variables as frequency, current, output voltage, cos
phi, power and the storage of the last 4th alarms
attempted.
Warning!
Electrical equipment can be a source of hazards. It is essential to fully understand
how to use this equipment and all relevant safety devices before attempting to
operate it.
The equipment must only be used by qualified technical personnel who are fully
aware of how to install and operate it in compliance with all relevant safety
standards, and who are perfectly able to understand all the associated
hazard warnings. The capacitors installed inside this equipment operate at
extremely high voltages. After switching off, wait for at least 5 minutes before
performing any work on the equipment. Even when the motor is switched off,
dangerous voltages can be present at the power terminals L1, L2 , L3, -, R, +, U,
V, W.
The machine can re-start automatically after a power failure under certain
programmingconditions.
There are no user serviceable parts inside the equipment. Only the front panel
must be removed for installation.
Technical specifications
Power Nominal
Inverter
supply output
power
voltage current
Vac kVA
DSV-030 5,4 7,5
DSV-040 6,5 9,0
230V-15%
DSV-055 9,1 12,5
460V+10%
DSV-075 12,3 17
50-60Hz
DISPLAY
DSV-110 3-phase 18,1 25,0
OLr
DSV-150 23,9 33,0
Ot
PHI DSV-185 27,5 38,0
-
Err
This document is a quick guide to the installation and
P.Err
operation of the inverter. For safe, advanced use, refer to
r
C.Er
the complete manual which is available on request.
TDE Macno s.p.a.
Via dell'Oreficeria, 41 Fax. +39-044.343509
36100 Vicenza (VI) Italy
QUICK START
DIGITAL INVERTER
SIZE T1 - T2
Phase Phase Motor
current current Power Size
@230V @400V @400V
A A A kW
8,9 10,0 3,0 T1
10,7 12,0 4,0 T1
14,7 16,5 5,5 T1
20,0 22,5 7,5 T1
28,9 32,5 11,0 T2
38,3 43,0 15,0 T2
44,1 49,5 18,5 T2
Tel. +39-0444.343555
MADSVX0030E0 V01
sw. 0D.07-xx.00
www.tdemacno.it