Table of Contents
Advertisement
Electrical Cabinets
Check to ensure that electric oven/contactor assembly is
activating.
Safety Related Circuits
Complete an operational check of the safety hi-limit
thermostats.
Make a complete operational check of all operating controls.
Microprocessor Programs / Selections
Each microprocessor controller (computer) has been
preprogrammed by the factory with the most commonly used
parameter (program) selections. If computer program
changes are required, refer to the computer programming
manual, which was shipped with the cabinet.
Preoperational Instructions __________
Preparing the Gear
Liner and shell should be washed separately and should
not be reassembled before drying. To dry, arrange gear as
follows: shell, liner, shell, liner, etc.
Microprocessor Controller (Computer)
IMPORTANT: For more detailed information regarding the
microprocessor controller (computer), refer to the
microprocessor user's manual included with the cabinet.
The L.E.D. display reads "READY" (no cycle in progress).
Press the letter on the keypad corresponding to the cycle
desired (e.g. key "D"). Then press START/ENTER button.
The cabinet will then start.
The L.E.D. display will read MANUAL DRYING CYCLE D,
___MIN REMAIN.
NOTE: The cabinet can be stopped at any time by pressing
the "STOP/CLEAR" key, at this time the cabinet will go into a
cycle pause. If the "STOP/CLEAR" key is pressed again at
this point, the cycle that was in progress will be cancelled
and returned to the "READY" state.
When the programmed drying time has expired, the non-
coin microprocessor controller (computer) will proceed into
the Cool Down Cycle.
Once the Cool Down Cycle begins at the end of the heat
cycle, the L.E.D. display will read COOL DOWN TEMP __/__
MINUTES remaining. At the end of the heat cycle, the cabinet
will shut off the heat and continue the fan until the Cool
Down Time or temperature is reached.
Shutdown Instructions _______________
If the cabinet is to be shutdown (taken out of service) for a
period of time, the following must be performed:
Discontinue power to the cabinet either at the external
disconnect switch or the circuit breaker.
Discontinue the heat supply:
12
Gas Models – Discontinue the gas supply.
Shut off external gas supply shutoff valve.
Shut off internal gas supply shutoff valve located in the gas
valve burner area.
Steam Models – Discontinue the steam supply.
Shut off external (location furnished) shutoff valves.
Remove the door.
Service / Parts Information __________
Service
Service must be performed by a qualified trained technician.
If service is required, contact the reseller from whom the
equipment was purchased. If the reseller cannot be
contacted or is unknown, contact the Service Department
for a reseller in your area.
NOTE: When contacting the Service Department, be sure to
give them the correct model number and serial number so
that your inquiry is handled in an expeditious manner.
Parts
Replacement parts should be purchased from the reseller
from whom the equipment was purchased. If the reseller
cannot be contacted or is unknown, contact the Parts
Department for a reseller in your area. Parts may also be
purchased directly from the factory by calling the Parts
Department at +1 (508) 678-9000 or you may FAX in your
order at +1 (508) 678-9447.
NOTE: When ordering replacement parts from the reseller
or the manufacturer, be sure to give them the correct model
number and serial number so that your parts order can be
processed in an expeditious manner.
Warranty Information ________________
Returning Warranty Cards
Before any gear cabinet leaves the factory test area, a
warranty card is placed on the inside of the main door glass.
These warranty cards are intended to serve the customer
where we record the individual installation date and warranty
information to better serve you should you file a warranty
claim.
If a warranty card did not come with your gear cabinet, contact
the Warranty Department or the Service Department at
+1 (508) 678-9000.
IMPORTANT: A separate warranty card must be completed
and returned for each individual gear cabinet.
NOTE: Be sure to include the installation date when returning
the warranty card(s).
Warranty
For a copy of the commercial warranty covering your particular
gear cabinet(s), contact the reseller from whom you
purchased the equipment and request a cabinet warranty
form. If the reseller cannot be contacted or is unknown,
warranty information can be obtained from the factory by
contacting the Warranty Department at +1 (508) 678-9000.
American Dryer Corp.
113015 - 5
- Quick Links:
- Preparation for Operation / Start-Up
Hide quick links:
Advertisement
Table of Contents
