Related Manuals for GE Becker HPP-5
Summary of Contents for GE Becker HPP-5
- Page 1 GE Oil & Gas HPP-5 High Pressure Positioner Installation and Maintenance Manual GE Data Classification : Public...
-
Page 2: Table Of Contents
Description The Becker HPP-5 positioner is used in control valve assemblies with a controller or I/P transducer and double acting actuator to provide accurate flow or pressure control� The HPP-5 positioner can be used with various valve types that use a double acting pneumatic piston actuator�... -
Page 3: Technical Assistance
G = Specific Gravity of Gas T = Operative Temperature (°F) C V = Flow Factor P 1 = Supply Pressure to Positioner (psig) © 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 2... -
Page 4: Accessories
This decreases the pressure in the cylinder top, while the pressure in the cylinder 3 | GE Oil & Gas © 2014 General Electric Company. All rights reserved. -
Page 5: Open On Increasing
This one or two digit number will be the diameter in inches (for example, a unit with the model number 6H8F6FG-H4 has an 8-inch bore)� © 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 4... -
Page 6: Deadband Setting
Once the actuator has reached its desired position (based on the mid-signal applied to the instrument port – Step 5), place the block valve in the closed position� 5 | GE Oil & Gas © 2014 General Electric Company. All rights reserved. -
Page 7: Bias Adjustment
© 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 6... -
Page 8: Conversion To Split Range
Stroke Close on Open on Reference (see piping schematic provided by GE), then reattach to Increasing Increasing Drawings the positioner� This will allow the positioner to maintain the 4 inch... -
Page 9: Parts Ordering
2� ________ Replace rubber goods using Becker Model HPP-5 Single-Acting Positioner Repair Kit (Part # 30-9601) if necessary� 3� ________ Confirm power gas supply pressure is correct� Refer to original GE invoice paperwork for proper power gas setting� 4� ________ Observe operation of gages and replace if defective�... -
Page 10: Open On Increasing (Parts)
HPP-5 Positioner Parts List 9 | GE Oil & Gas © 2014 General Electric Company. All rights reserved. - Page 11 HPP-5 Positioner Appendix © 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 10...
- Page 12 HPP-5 Positioner Appendix 11 | GE Oil & Gas © 2014 General Electric Company. All rights reserved.
-
Page 13: Assembly Procedure
2a� Turn valve adjusting screw (H) into the inside piston (I) until the screw head is flush with the piston recess� © 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 12... - Page 14 Step 1� (vertical cross hole must be blocked with plastic plugs in order to check exhaust port)� 4d� Remove all plugs from all blocks/manifolds [K and N]� 13 | GE Oil & Gas © 2014 General Electric Company. All rights reserved.
- Page 15 6d� Tighten the assembly with 1/2-20 hex jam nut (YY) onto the outside piston (I) to 95-100 in� lbs� 6e� To assemble the inside piston (W), repeat Steps 6-6d� © 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 14...
- Page 16 (MM)� Step 14. Bolt pressure cartridge (RR) to beam spacer (JJ) with six 1/4 - 20 x 1-inch hex head cap screws SS)� 15 | GE Oil & Gas © 2014 General Electric Company. All rights reserved.
- Page 17 © 2014 General Electric Company. All rights reserved. Becker HPP-5 High Pressure Positioner Maintenance and Operation Manual | 16...
Need help?
Do you have a question about the Becker HPP-5 and is the answer not in the manual?
Questions and answers