Delta DVPDT01-S Instruction Sheet

http://www.delta.com.tw/industrialautomation/
DVPDT01-S
Instruction Sheet
DeviceNet-Network Adapter
1 WARNING
This Instruction Sheet only provides descriptions for electrical specifications, general specifications,
installation and wiring.
This is an OPEN TYPE Controller. The DVPTD01-S should be kept in an enclosure away from airborne
dust, humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some
special tool or key to open the enclosure, so as to avoid the hazard to users or any damage to the module.
Do NOT touch terminals when power on.
2 PRODUCT INTRODUCTION
Functions:
• Support Group 2 only servers.
•
Support explicit connection via Predefined Master/Slave Connection Set. (Explicit message)
•
Support Polling connection.
• Connection size is fixed to 4bytes input and 4bytes output.
•
Support EDS file configure in DeviceNet configuration tools.
Nameplate Explanation:
Model name
Power supply spec.
24 V dc 1 W
Barcode & Series no.
D T0 1 - S 0 T 54 0 0 0 0 1
Model Name and Serial Number Explanations:
Serial Number
Model Serial Number
Product Series
For SS/SA/SX/SC MPU
Model type
Model number
PF: Profibus network module
Product Profile:
4 6 1. Model name
2. Extension port
POWER
3
3. Power, MS, NS LED
MS
NS 5 5
4. Extension hole for mounting
1
x10
2
7
unit or module
5 5
0
x10
5. DIN rail clip
1
DR 1
8
DR 0
IN 1 6. Extension clip
IN 0
7. Address switch
4
9 8. Manual switch
9. DeviceNet connection port
5
6
3 SPECIFICATION
2006-02-20
Item
DeviceNet Connection
Interface
Transfer method
5011643400-TTE0
Transfer cable
Electrical isolation
Communications
Message types
Baud Rates
Product Code
Product Type
Vendor ID
Electrical Specification
DeviceNet
Environmental Specifications
Noise Immunity
Environment
Vibration / Shock
Resistance
Standard
4
Profile
M A D E I N X X X X X X
POWER
MS
NS
Production series
Production week
Production year (2005)
Production plant (Taoyuan)
Serial number of version
Production Model
Install DVPDT01-S with PLC MPU
POWER
RUN
ERROR
BAT.LOW
RUN
STOP
0
1
Specification
Pluggable connector (5.08mm)
CAN
2-wire twisted shielded cable with 2-wrie bus power cable and drain
500V DC
I/O Polling
Explicit
125 K bps
250 K bps
500 K bps
80
12
799 (Delta Electronics Inc.)
Module supply voltage: All other power derived from PLC controller power supply
Network input current: less than 50mA (24V DC)
ESD(IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge
EFT(IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV,
Analog & Communication I/O: 1KV
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS(IEC 61131-2, IEC 61000-4-3): 26MHz~1GHz, 10V/m
Operation: 0℃~55℃ (Temperature), 50~95% (Humidity), Pollution degree 2;
Storage: -40℃~70℃ (Temperature), 5~95% (Humidity)
Standard: IEC1131-2, IEC 68-2-6（TEST Fc）/ IEC1131-2 & IEC 68-2-27 (TEST Ea)
IEC 61131-2,UL508 standard
INSTALLATION AND CONFIGURATION
Dimensions are in millimeter and [inch]
5 5
1
x10
5 5
0
x10
DR 1
DR 0
IN 1
IN 0
s POWER
s
MS
X0
NS 5 5
X1
x10 1
X2
X3
5 5
X4 0
x10
X5
X6
DR 1
X7 DR 0
IN 1
C0 IN 0
Y0
C1
Y1
C2
Y2
Y3
Pin Definition of DevicetNet Connector
Pin Signal Color Content
1 V- Black 0 VDC
2 CAN_L Blue Signal-
3 Drain - Shield
4 CAN_H White Signal+
5 V+ Red 24 VDC
MAC ID Setting
Switch setting Content
0 ... 63 Valid DeviceNet MAC ID setting
95 Set module entry update mode
Other Invalid DeviceNet MAC ID setting
Function Switches Setting
DR1 DR0 Baud rate
OFF OFF 125K bps
OFF ON 250K bps
ON OFF 500K bps
ON ON Auto Baud rate (not recommend)
ON – Hold the input and output buffer data when unit
loss the DeviceNet communication.
IN0
OFF – Clear the input and output buffer data when unit
loss the DeviceNet communication.
IN1 Reserved
Connect DVPTD01-S to DeviceNet
Connection Example:
PC Master
POWER s POWER
s
RUN
MS
X0
ERROR
NS 5 5
BAT.LOW X1
x10
X2
X3
5 5
RUN X4
x10
X5
X6
DR 1
X7
STOP DR 0
IN 1
C0 IN 0
Y0
C1
Y1
C2
Y2
Y3
0
1
Data Mapping:
DVPDT01-S provides users with fixed 4bytes input data and 4bytes output data in DeviceNet network. 4bytes input
data are transmitted from DVPDT01-S module to DeviceNet Master and they are mapping to Y20-Y57 in PLC
controller when DVPDT01-S is the first extension unit of PLC. 4bytes output data are transmitted from DeviceNet
Master and they are also mapping to X20-X57 in PLC controller.
5
4
3
2
1
5
5
DeviceNet network
DVP-PS01
DVP-12SA
DVP-DT01
1
0