Advertisement
7. MAINTENANCE
7.1.
Daily Maintenance Check
7.1.1. Check the state of the wheels and the axles since thread, rags and other foreign objects can jam the wheels making safe, effective
operation difficult.
7.1.2. On completion of each task, unload the forks and return them to the lowest position.
7.2.
Oil Check
7.2.1. Check the oil level at six monthly intervals. Sealey hydraulic jack oil is used with the pallet truck. The viscosity of the oil should be
30cSt at 40°C. The amount used in the pallet truck is approximately 0.4 litres.
7.3
Lubrication
7.3.1. The bearings and shafts of the pallet truck have long-life grease applied to them during manufacture. The bearings will only require
.greasing at monthly intervals or after the pallet truck had been serviced down to the lubrication points.
7.4.
Purging Air from the Hydraulics
7.4.1. Air can get into the hydraulic oil through transportation, or the pump becoming misaligned. As a result, the forks will not elevate.
7.4.2. The air can be purged by setting the control level to the LOWER position and pumping the operating handle up and down for 30 - 40
seconds.
7.4.3. When the pallet truck is not in use, lower the forks and park the truck where it will not be a hazard.
7.5.
Battery Replacement
7.5.1. To insert batteries, first remove the back cover at the rear of the console display unit.
7.5.2. Insert 4XAA cells making sure that they are correctly placed in the display unit.
7.5.3. Replace the cover on the display unit
8. TROUBLESHOOTING
8.1.
Troubleshooting on the pallet truck.
Problem
The forks cannot be raised to their maxi-
mum height,
The forks cannot be raised.
The forks cannot be lowered
The forks lower without the release valve
operating.
8.2.
Fault-finding on the weighing unit.
Problem
HELP1 on display
Scale is not accurate
Display won't turn on.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey Limited
Cause
- Their is insufficient oil in the reservoir.
- No hydraulic oil or impurities or air in the oil.
- The adjusting nut (fig.2D) is too high keeping the
pumping valve open.
- Air has entered the hydraulic system.
- The piston rod (fig.2A) or the pump is
deformed.
- Forks have been kept in the rise position
resulting in the rod jamming.
- The adjusting nut or bolt is incorrectly positioned.
- Impurities, or air, has got into the release valve
oil.
- Parts of the hydraulic system have been
damaged.
- Adjusting nut (fig.2D) or bolt (fig.3F) incorrectly
positioned.
Cause
- The load is too heavy for the scale.
- The fork shoe is touching the bottom part of the
scale.
- Cable in junction box is loose.
- One of the load cells is broken.
- Battery voltage is too low.
- Battery life is complete.
sales@sealey.co.uk or phone 01284 757500.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Solution
- Replenish the oil to the correct level.
- Replenish or change the oil.
- Reset the adjusting nut or bolt (fig.2E).
- Purge the air from the hydraulic system.
- Replace the piston rod or pump.
- Keep the forks in the lowest position when
not in use.
- Adjust the nut or bolt.
- Replace the oil and/or purge the air from
valve.
- Inspect and replace the damaged parts.
- Adjust the nut (fig.2D) or screw (fig.3F).
Solution
- Remove the load immediately
- Remove anything that restricts movement
of the scale.
- Check the connection in the junction box
and confirm it is secure.
- Apply weight to all four corners of the
scale and the load cell with the different
weight should be replaced.
- Change the batteries.
- Change the batteries.
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
PT1150SC.V2 Issue:3(SP)-26/04/13
Advertisement
