Advertisement
STEPS TO
PROGRAMMING
WARNING These steps
involve working with hot
water. Scalding may occur if
care is not taken against spilling.
ENTERING THE PROGRAM MODE #1
For ALL functions you must first enter the programming mode.
Turn OFF the power from the Control Panel by pressing
Press and HOLD
and press and RELEASE
Continue HOLDING
ENTER THE PROGRAM MODE #2
For ALL functions you must first enter the programming mode.
Turn OFF the power from the Control Panel by pressing
Press and HOLD
and press and RELEASE
Continue HOLDING
until
ENTER THE PROGRAM MODE #3
For ALL functions you must first enter the programming mode.
Turn OFF the power from the Control Panel by pressing
Press and HOLD
and press and RELEASE
Continue HOLDING
until
2
PROGRAMMING ONLY REQUIRED IF FACTORY SETTINGS MUST BE CHANGED
Changing the ADS™ System Program
Your ADS System features a dynamic memory. In the event of a power loss it will remember ALL program settings.
IMPORTANT – Before entering the program mode, allow the unit to reach brewing temperature, then press the BREW
button to dispense at least 12 ounces of water. This is to clear any air that may be trapped within the water lines.
Brew Temperature – Factory Pre-Set to 204°F
Function to set brew temperature, 170° to 210°F. Brew temperature will be indicated by READY-TO-BREW light blinking.
.
.
until
starts blinking; RELEASE.
READY TO BREW
BREW VOLUME - Factory Preset to Brewer Requirements
BREW CYCLE COUNTER
.
.
STOPS blinking; RELEASE.
READY TO BREW
CHANGING THE DRIP MODE (DWELL TIME) FEATURE
.
.
STOPS blinking and remains on.
READY TO BREW
CONFIRM/RESET BREW TEMPERATURE - Factory Preset to 204º
ENTER THE PROGRAMMING MODE #1:
Press
for two seconds, then RELEASE.
will start blinking. Each blink equals 2º F, starting at 170º (max. temp. 210º F or 21 blinks).
READY TO BREW
To change Temperature, press and HOLD
.
will start QUICK flashing. Each QUICK flash equals 2º F.
READY TO BREW
After reaching 210º, temperature starts over at 170º.
RELEASE
when the desired temperature is reached. The newly set temperature will now be displayed.
To set and exit, press
.
CHANGE BREW VOLUME - CONCENTRATE
ENTER THE PROGRAMMING MODE #1
Press and HOLD
until hot water starts running from sprayhead; then RELEASE.
When desired volume is reached, press
To set and exit, press
.
CHANGE BREW VOLUME - DILUTION
ENTER THE PROGRAMMING MODE #1
Press and HOLD
until cold water starts flowing from dilution faucet; then RELEASE.
When desired volume is reached, press
To set and exit, press
.
TO ACCESS BREW CYCLE COUNTER
ENTER THE PROGRAMMING MODE #2:
will now start a pattern of LONG and SHORT blinks.
READY TO BREW
This pattern identifies the number of brew cycles. SHORT blinks indicate the brew number from one [1] to nine [9].
LONG blinks separate the 1's, 10's, 1,000's and 10,000's.
ENTER THE PROGRAMMING MODE #3
The
will now blink a pattern of flashes from one
READY TO BREW
to ten. The first blink, if selected = 30 seconds; after that, each blink is one minute.
Illustrated Parts List - TCTD-35/35S Curtis
Illustrated Parts List - TCTD-35/35S Curtis
Illustrated Parts List - TCTD-35/35S Curtis
Illustrated Parts List - TCTD-35/35S Curtis
Illustrated Parts List - TCTD-35/35S Curtis
Iced Tea Brewer
Iced Tea Brewer
Iced Tea Brewer
Iced Tea Brewer
Iced Tea Brewer
ITEM
ITEM
ITEM
ITEM
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14A
15
16
.
again to stop flow.
again to stop flow.
Note: Dwell time setting has an affect on
dilution water flow (even though the Drip
Mode starts at the end of brewcycle). Drip
modes set at 7 minutes or less results in
pulsing dilution flow. Drip modes set at 8 minutes or
more results in continuous flow of dilution water.
PART N
PART N
PART N
PART N
PART Nº º º º º
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
WC-3322
BASKET, WIRE 6.4 DIA PTTD/TCTD USE W/WC-3320
WC-3647
STRAINER BT-10 BREWCONE (EXCEPT PARADISE)
WC-3320
BREW CONE W/HANDLE 8.8" D W/STRAINER
WC-3201
HANDLE, BREW CONE BLACK
WC-3358
BREWCONE ASSY, W/WC-3320, WC-3322 & WC-3647
WC- 750
CONTROL BOARD 120V 60Hz PTTD/TCTD
WC-5450
COVER, TOP BREWER
WC-2977-01
FITTING ASSY, SPRAYHEAD W/O-RING
WC-39260
MEMBRANE CONTROL PANEL, TCTD
WC-2965
SPOUT, BYPASS ASSY
WC-2906
SPRAYHEAD, BLUE .178 DIA ORF
WC-8556
HEAT SINK ASSY DV
WC- 895
VALVE, DUAL INLET 120V 10W
WC-58017
COVER, CENTER WRAP TCTD-35S
WC-58021
COVER, FRONT CENTER WRAP TCTD-35
WC-3502
LEG, 8-32 STD SCREW BUMPER
WC-8531
RAIL, BASE TCTD
Continued – Page 3
Advertisement
