Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AMT Quantum7
Summary of Contents for AMT Quantum7
-
Page 9: Transmitter Features
Transmitter Features Handheld Transmitter Option 1. Microphone head with cartridge inside 2. Metal pipe (Aluminum alloy) Anodize any different colors, never fade. 3. Backlit LCD Display group, channel, frequency and battery life. 4. IR infrared port Receiver infrared beam to synchronize frequencies, hold the transmitter with its IR port facing directly towards the receiver’s IR port with a distance between 5-20cm. - Page 11 Acoustic Instrument Transmitter 1.Each AMT microphone has a disconnect. (D.C.T.) Connect the cable from the Q7 Transmitter to the 3pin (Ta3) input connector on the microphone. 2.Adjustable Gooseneck Adjustable at angle to allow sound to escape from instrument and develop naturally.
-
Page 12: System Setup
System Setup 1.Connect the included AC power supply to the rear of the receiver and turn on the receiver. 2.Standard Display The standard display shows the preselected group and channel. Group Push the SET button and hold for 1 second, the GROUP icon will blink. Push the up and down buttons to set the desired group (01-10), Press SET again to confirm. - Page 13 System Setup IR Sync After setting channel, press the SET again, the IR Icon will blink (picture 1). Push the SET button and hold for 1 second, the receiver will start to send the infrared signals (picture 2), then put the transmitter (handheld, body-pack or musical instrument) IR port close to the receiver’s IR port.
- Page 14 System Setup Transmitter / Receiver IR Quick Sync With the receiver in normal operating mode, and the TRANSMITTER OFF, push and hold the SET button on the receiver to sync the transmitter to the receiver. While the receiver is sending the signal, turn the transmitter ON. If, for some reason, your transmitter is not on the same channel from the last usage, you can use the IR Quick Sync method to quickly sync the transmitter without having to page through the group and channel setting functions.
-
Page 15: Specifications
Specifications Receiver Frequency Preparation PLL Synthesized Control （ ） Frequency Range 600-952MHz Region dependent Frequency Type Modulation Type Channels 100(10x10) Oscillation System Type of reception True Diversity ≥ Receive Sensitivity -11dBm (sinad 30dB) Frequency Response 60Hz-17KHz+/-3dB ≥ S/N Ratio 105dB T.H.D <0.5% at 1KHz Dynamic Range... -
Page 16: Body-Pack Transmitter
Specifications Body-pack Transmitter Frequency Preparation PLL Synthesized Control Frequency Range 600-952MHz(Region dependant) Frequency Deviation ±48KHz Input 3 pin mini-XLR RF Output Power 10mW Controls Power ON//OFF, Volume, SET frequency Indicators LED (PO), LCD(BATT, frequency) Interface Infrared Antenna 1/4 wave Length Wire Type Power Supply 2*AA battery Operating Voltage... - Page 17 Frquency List 606-614（100CH，10*10） 第1组信道 第 2组信道 第 3组信道 第 4组信道 第 5组信道 Group 1 Group 2 Group 3 Group 4 Group 5 CH1=606.00MHZ CH1=606.80MHZ CH1=607.60MHZ CH1=608.40MHZ CH1=609.20MHZ CH2=606.08MHZ CH2=606.88MHZ CH2=607.68MHZ CH2=608.48MHZ CH2=609.28MHZ CH3=606.16MHZ CH3=606.96MHZ CH3=607.76MHZ CH3=608.56MHZ CH3=609.36MHZ CH4=606.24MHZ CH4=607.04MHZ CH4=607.84MHZ CH4=08.64MHZ CH4=609.44MHZ CH5=606.32MHZ...
- Page 18 Frquency List 863-865MHz（16CH, 4*4） 第 1组信道 第 2组信道 第 3组信道 第 4组信道 Group 1 Group 2 Group 3 Group 4 CH1=863.000MHZ CH1=863.500MHZ CH1=864.000MHZ CH1=864.500MHZ CH2=863.125MHZ CH2=863.625MHZ CH2=864.125MHZ CH2=864.625MHZ CH3=863.250MHZ CH3=863.750MHZ CH3=864.250MHZ CH3=864.750MHZ CH4=863.375MHZ CH4=863.875MHZ CH4=864.375MHZ CH4=864.875MHZ 902-928MHz（100CH, 10*10） 第 1组信道 第...
- Page 19 The specification won’t do any further notice for the improvement Actual product will not be as pictured...
Need help?
Do you have a question about the Quantum7 and is the answer not in the manual?
Questions and answers