Advertisement
Quick Links
Advertisement
Related Manuals for Ramix PMC665
Summary of Contents for Ramix PMC665
- Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
- Page 2 PMC665 Intelligent Dual ETHERNET Interface Card Hardware Reference Installation Manual Document ID Rx-URME-007 Revision: Rev - Issue Date: April 25, 2001 1672 Donlon Street, Ventura, CA 93003 U.S.A., Tel: (805) 650 2111, FAX: (805) 650 2110 Customer Support E-mail: support@ramix.com...
- Page 3 The information in this manual has been carefully reviewed and is believed to be entirely accurate. However, RAMiX shall not be liable nor responsible for errors contained herein. RAMiX reserves all rights to make any changes to improve the reliability, function or design, without any notice.
-
Page 4: General Information
PMC665 PMC Module. The PMC665 is an Intelligent Dual Ethernet interface card, offering two, fully independent 100 Mbit Ethernet channels using multi mode Fiber media (100BaseFx). Designed to be plugged onto a host processor (e.g., Single Board Computer) board, the PMC665 provides an extremely compact, economical high performance Ethernet solution. Incorporating an on-module I/O co-processor, the PMC665 allows off-loading of the host processor of high over tasks. -
Page 5: Hardware Installation
If the container is damaged, request that the carrier’s agent be present during unpacking and inspection of the unit. Unpack the PMC665 module from shipping carton. Check to verify that all items are present by referring to the packing list. 2.2.1... - Page 6 Use the four screws to connect the PMC665 stand offs to the host PCB Connection to the Local Network Media The PMC665 has two fiber transceiver connections on the front panel, one for each Ethernet channel. Connection is made using industry standard fiber cables.
- Page 7 Thus, control and data flow between the Co-processor and local memory system will consume no bandwidth on the Host PCI. It is this isolation that allows the PMC665 to perform arbitrary manipulation, filter, etc., of data from the Ethernet, without compromising the host system performance.
- Page 8 • with all low level control resident in the co-processor How the PMC665 responds to PCI configuration requests from the host can be altered by on- board firmware. Upon power-up (or reset), the on-board processor performs a Built-In-Test (BIT) sequence of the internal (Bridge/co-processor) operation, local memory subsystem and Ethernet controllers.
- Page 9 Note: (Direct data transfer is not a requirement for sustaining maximum performance. The 100+ Mbytes per second bandwidth of each of the busses on the PMC665, combined with their independent operation provides substantial margin in store (filter) and forward operations.
-
Page 10: Front Panel Indicators
PMC665ST/R Top Ports Transmit Transmit (Primary) Bottom Link Link Ports Receive Receive PMC665ST/R Rx-URME-007 Rev - - Preliminary - PMC665 Hardware Reference and Installation Manual Page 9 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... -
Page 11: Specifications
1.5A @ 3.3V, typical 1.3A @ 3.3V Power Max. 300mA @ 5V, typical 210mA @ 5V Rx-URME-007 Rev - - Preliminary - PMC665 Hardware Reference and Installation Manual Page 10 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... - Page 12 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Need help?
Do you have a question about the PMC665 and is the answer not in the manual?
Questions and answers