Related Manuals for Leuze electronic HFU 4500D
Summary of Contents for Leuze electronic HFU 4500D
- Page 1 HFU 4500D combined mobile RFID- and 1D / 2D Code- hand held reader with cable Short Description Version V 2.01...
-
Page 2: Table Of Contents
Note This document is just for information about how to use the mobile combi device HFU 4500D from Leuze electronic. All important details about the functionality and the handling were described further on. In addition the typical connections together with the modular connector units (MA) are in this manual, too. -
Page 3: Delivery Contents
THERNET ................F ONNECTION TO NTERBUS EHLER EXTMARKE NICHT DEFINIERT Delivery contents HFU 4500D 1. Mobile combi RFID + 1D/ 2D code-Hand held reader 2. RS232 spiral cable, 4m length 3. Bypack paper Short description HFU 4500D Leuze electronic Page... -
Page 4: Safety Notices
Attention! Access to or changes on the device, except where expressly described in this document, are not authorized. Qualified personnel Mounting, commissioning and maintenance of the device must only be carried out by qualified personnel. Electrical work must only be carried out by a certified electrician. Short description HFU 4500D Leuze electronic Page... -
Page 5: Installation
5. With the black marked keys the function is selected and with the yellow marked key activated. Settings for data output, code types etc. can be set in the ‚system‘ area (right yellow key). Short description HFU 4500D Leuze electronic... -
Page 6: How Is The Best Way To Scan Or Read
The read characteristics are printed on page 8 Test barcode The printed code is to test the functionality of the scanner, module(bar) width is 0.5 mm (20 mil) Code 39 Bar Code Sample Short description HFU 4500D Leuze electronic Page... -
Page 7: Technical Data
Valid Standards EN 301489-3 EN 302208-1 Protection class IP54 Temperature (operation) -20 to 50 °C (storage) -20 to 50° C * depends on used Transponder **depends on used optical 1D / 2D code type Short description HFU 4500D Leuze electronic Page... -
Page 8: Read Characteristics
ECC200, PDF, QR, Maxicode, GS1-codabar Familiy Cell size: 0.21 to 0.9mm, Working area RFID Antenna TFU05 TFU10 450mm Readable Transponder-Types: EPC1Gen2 (NXP G2XM, GSXL, Alien Higgs3 Out of ISO18000-6C) Using the HFU 4500D Short description HFU 4500D Leuze electronic Page... -
Page 9: Functions
In any case the device comes back with a message (success/ failure) onto Display / Interface. The sequence is fixed, an interrupt is only possible with C. All parameter settings can be found in the sub menus inside the system area/barcode and RFID (see menu structure). Short description HFU 4500D Leuze electronic... - Page 10 (activate Messages) with “SFC0” when no function is selected, “SFC1” with selected function 1 (SCAN Barcode) etc. (see no 3.) Note: Please combine Commands and Data (characters or numbers) directly (without space between) into One single telegram, enclosed of the telegram prefix/suffix Short description HFU 4500D Leuze electronic Page...
-
Page 11: Device Reset / Factory Default
Note: All individual settings are lost then!!! Parameter Setting All parameters are available and can be set via key board in different sub menus within the system menu. No separate or special software tool is needed. Short description HFU 4500D Leuze electronic Page... -
Page 12: Telegram- / Command Structure
Telegram- / Command structure The factory presets are similar to the other available fix mounted RFID- devices from Leuze electronic. The Standard telegram structure is shown below, with 9600Bd, 8 Databits , N,1 : Command CR LF ASCII-Character 0Dh 0Ah For this device you can change the telegram frame and the Baudrate. -
Page 13: Menu Structure
Type in Start block no. and No of Blocks, factory 05 RFID Write Data output PREfix Type in Telegram-Start character, factory STX SUFfix Type in Telegram-End character , factory 0D,0A Select ASCII / HEX, ab Werk ASCII Data format Short description HFU 4500D Leuze electronic Page... - Page 14 ON/OFF for Send Messages via Interface, factory OFF ON/OFF for Send NORead Message, factory OFF NO Read ON/OFF for Inputline to type in Quantity, factory OFF USE Qty Qty separator Choose separator sign for Quantity in output telegram Short description HFU 4500D Leuze electronic Page...
- Page 15 * Note: The availability of the memory banks TID (serial number), EPC and User block depends on the used transponder chip and may be not always available. The EPC bank is typically available with 8 – 12 characters and 4-6 blocks at any chip type. Short description HFU 4500D Leuze electronic...
-
Page 16: Hfu 4500D At Serial Pc-Interface
HFU 4500D at serial PC-Interface With power supply via PIN 9 via RS232-cable neccessary parts: 50113280 HFU 4500D, incl. cable 4m length Pinning of the 9 Pol- D-Sub (female) PIN-No Signal Description Transmit Data (-5 to +5V) Recieve Data (-5 tos +5V) -
Page 17: Hfu 4500D With Ma 204I, Ma208I Or Ma248I
HFU 4500D with MA 204i, MA208i or MA248i RS 232 with 9600 Baud, 8 Data bits, 1 Stoppbit, No Parity, Postfixes CR/LF. Necessary parts: 50113280 HFU 4500D, incl. cable 4m length 50113397 KB JST-HS-300, 5VDC at PIN9 50112891 MA 248i for... -
Page 18: Hfu 4500D With Usb (Com-Port-Emulation)
HFU 4500D with USB (COM-Port-Emulation) To use the HFU45xxD with USB you use the standard RS232 cable and connect the USB Converter cable. The data is sent to the new COM-Port. The necessary driver is available on www.leuze.de. the interface is set to 9600,8,N,1.Separate power supply needed. -
Page 19: Diagnostics And Trouble Shooting
7. RFID: Please check the settings for RFID and check the transponder type with your supplier. If the settings are correct the transponder can be defect as well- try another one if possible. 8. Now you checked most possibilities. For further support please contact the Leuze Service. Short description HFU 4500D Leuze electronic... -
Page 20: Type Overview
Type overview HFU 45xx – Series Art-No. Description Interface Picture HFU 4500D, incl. Cable 4m 50113280 TTL RS232 Accessories Accessories for HFU 45xx Picture Art-No. Discription NT Hx5x0, external Power supply for HFM/HFU, 50110676 Base Hx520 (100-240VAC/6VDC) USB-converter cable for HFM/ HFU,... - Page 21 • Art-No. 50113397 Leuze electronic GmbH+Co.KG Postbox 1111 In der Braike 1 D-73277 Owen / Teck Tel +49 (07021) 573-0 Fax +49 (07021) 573199 E-mail: info@leuze.de State 09 / 2012 http://www.leuze.de Document TD_HFU4500D_en_50119342 Short description HFU 4500D Leuze electronic Page...