Table of Contents
Advertisement
Specifications (Continued)
List of supported signals (Component signals)
Signal format
480i(55i)@60Hz
480p(55p)@60Hz
576i(65i)@50Hz
576p(65p)@50Hz
70p(750p)@60Hz
70p(750p)@50Hz
1080i(115i)@60Hz
1080i(115i)@50Hz
1080p(115p)@60Hz
1080p(115p)@50Hz
List of supported signals (Video, S-Video signals)
Video mode
fh(kHz)
NTSC
15.7
PAL
15.6
SECAM
15.6
PAL-M
15.7
PAL-N
15.6
PAL-60
15.7
NTSC4.4
15.7
Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN and
MONITOR terminals
11
15
6
10
1
5
Mini D sub 15 Pin connector
Input Signal
•
RGB input
RGB signals:
0.7V(p-p) 75Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal:
TTL level (Pos/neg polarity)
•
Y/P
/P
input
B
R
1.0V (p-p) 75 Ω
Y signal:
P
/P
signals:
0.7V (p-p) 75 Ω
B
R
fh(kHz)
fv(Hz)
15.7
59.94
1.47
59.94
15.6
50.00
1.5
50.00
45.00
60.00
7.50
50.00
.75
60.00
8.1
50.00
67.50
60.00
56.5
50.00
fv(Hz)
fsc(MHz)
60
.58
50
4.4
50
4.5 or 4.41
60
.58
50
.58
60
4.4
60
4.4
Pin description
Pin No.
During RGB input During Y/P
B
1
Video signal (R) Color difference signal (P
Video signal (G) Luminance signal (Y)
Video signal (B)
Color difference signal (P
∗
4
GND
5
GND
∗
6
GND(R)
GND(P
)
R
7
GND(G)
GND(Y)
8
GND(B)
GND(P
)
B
9
N.C
∗
10
GND
∗
∗
11
GND
1
N.C
∗
1
Horizontal sync signal ∗
Vertical sync signal ∗
14
∗
15
N.C
∗ Do not connect anything.
54
CONTROL terminal
Pin assignment
D sub 9 pin connector
Interface format
1. Communication method
. Communication format
. Data format
4. Replies
/P
input
R
If commands are to be sent consecutively, wait for the response from the projector
)
R
before sending the next command.
)
B
Main Commands
Item
Power on
Power off
Icon display on
Icon display off
Auto setting (RGB input)
Status display on
Status display off
Note
•
Contact your dealer for control cable and other commands.
Pin No. Signal Name
1
DCD
Data carrier detect
TXD
Sending data
RXD
Receiving data
4
DTR
Data terminal ready
5
GND
Signal ground
6
DSR
Data set ready
7
RTS
Request to send
8
CTS
Consent to send
9
RI
Ring indicator
RS-C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length: 1 bit
STX (0h)
Command (Byte)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-
uppercase alphanumeric characters supported.
Acknowledge
ACK (06h)
CR(0Dh)
ACK (06h)
ESC(1Bh)
No acknowledge
NAK (15h)
Command
PON
POF
MO0
MO1
PAT
DON
DOF
55
Description
ETX (0h)
Data
... Normally ended
... Aborted
Advertisement
Table of Contents
