Advertisement
USING THE GRASS TRIMMER AS AN EDGE TRIMMER
5.7.
To cut the edges of lawns and flower beds, the grass trimmer can be converted as follows:
IMPORTANT Remove the battery pack.
5.7.1.
Push and turn the motor head through 90° in the required direction until it latches in place (fig.12).
5.7.2.
Now the grass trimmer has been converted to an edge trimmer that cuts vertically.
6. MAINTENANCE
WARNING! before cleaning the grass trimmer, pull out the battery pack.
‰
6.1.
CLEANING
6.1.1.
Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth
or blow it down with compressed air at low pressure.
6.1.2.
Always clean the equipment immediately after use.
6.1.3.
Clean the equipment regularly with a damp cloth and some mild soap. DO NOT use cleaning agents or solvents, these may be
aggressive to the plastic parts in the equipment. Ensure that no water can get into the interior of the equipment. The ingress of water
into an electric tool increases the risk of an electric shock.
6.1.4.
Use a brush to remove deposits from the safety guard.
6.2.
REPLACING THE BLADE
IMPORTANT Be sure to remove the battery pack before replacing.
6.2.1.
To remove the blade, push the blade inwards and remove it through the larger opening as shown (fig.13).
6.2.2.
To fit the new blade, proceed in reverse order. Make sure the blade locks into place correctly (fig.14).
6.3.
STORAGE
6.3.1.
Remove battery. Store carefully in a secure, dry place, out of the reach of children.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): . . . . . . . . . . .5.8 m/s²
Uncertainty value (k):. . . . . . . . . . . . . . . . . . . . . . . . . . .2.3 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that
a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures
can be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry
and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use
and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSE website
www.hse.gov.uk - Hand-Arm Vibration at Work.
Parts support is available for this product. Please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
WARNING! – Risk of Hand Arm Vibration Injury.
01284 703534
Original Language Version
sales@sealey.co.uk
www.sealey.co.uk
CS20V | Issue 1 10/12/18
Advertisement
