Air traffic control radar beacon system / mode select (atcrbs / modes) airborne equipment / transponder level 2es (50 pages)
Summary of Contents for Becker ATC 3401
Page 1
Transponder ATC 3401 - (1) - R INSTALLATI O N A N D O P E R A T ION Becker Flugfunkwerk Gm b H B a d e n A irpark / 77836 Rheinmünster / Germ a n y Telephone +49 (0) 7229-305-0 / Fax +49 (0) 7229-305-217 E -Mail : info@becker-avionics.de or support@becker-avionics.de...
Page 9
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R TABLE OF CONTENTS P a g e INTRODUCTION G E N E R A L I N F O R M A T I O N...
Page 17
INTALLATION AND OPERATION ATC 3401 - (1) - R ≥ 50 dB D y n a m i c r a n g e ± 3 MHz < 3 dB B a n d w i d t h Side lobe suppression...
Page 18
I N T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Polarization vertical Radiation omnidirectional Connection BNC socket Insulation resistance min. 1000 MΩ...
2-11 Fig. 2-5 D i m e n s i o n s A N T 2 0 0 0 2-12 Fig. 2-6 Installation wiring ATC 3401 - (1) - R 2-13 Page II-I 34-50-03 UNCONTROLLED COPY IF PRINTED June 15/96...
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R INSTALLATION General Installation of the transponder ATC 3401 - (1) - R depends on the aircraft type and its equipment. Therefore, only general information can be provided in this Section. Inspection before installation Before the transponder is installed in an aircraft, a visual inspection for possible transport damages shall be performed.
Page 24
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R ( 2 ) Checking side lobe suppression (SLS) Set SQUAWK/NAUT I to mode A on and 400 interrogations per second.
. Mechanical installation The ATC 3401 - (1) - R transponder is to be fitted at a suitable point in the aircraft. This is usually the avionics compartment. The dimensions necessary for the installation are shown in Fig. 2-2.
Page 26
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Pin connections of the unit connector Connector : P 8...
Page 27
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R P i n : A l t i t u d e p u l s e B 2...
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R DME suppression If required, connnect the suppression in/out of transponder (pin 10 of unit con- nector P8) with the corresponding pin of the DME unit with type RG 178 B/U cable.
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Checking after installation G e n e r a l After the installation, check the transponder to ensure satisfactory operation of the unit.
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R F i g . 2 - 1 T e s t s e t u p...
Page 31
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Fig. 2-2 Dimensions ATC 3401 - (1) - R Page 2-9 34-50-03...
Page 32
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R F i g . 2 - 3 D i m e n s i o n s C I 1 0 0 - 2...
Page 33
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Fig. 2-4 Dimensions DMNI 70-1 Page 2-11 34-50-03 UNCONTROLLED COPY IF PRINTED...
Page 34
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Fig. 2-5 Dimensions ANT 2000 Page 2-12 34-50-03 UNCONTROLLED COPY IF PRINTED...
Page 35
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R Fig. 2-6 Installation wiring ATC 3401 - (1) - R Page 2-13 34-50-03...
Page 36
I N S T A L L A T I O N A N D O P E R A T I O N ATC 3401 - (1) - R INTENTIONALLY BLANK Page 2-14 34-50-03 UNCONTROLLED COPY IF PRINTED June 15/96...
Need help?
Do you have a question about the ATC 3401 and is the answer not in the manual?
Questions and answers