Advertisement
Quick Links
SETUP
INSTRUCTIONS
UNDERWATER WIFI INSPECTION PACK
REV1.1 MAY
2018
INTRODUCTION
Congratulations on your purchase of the high quality telescopic carbon fibre pole and underwater
wifi cable pack. This document details the setup instructions for safe and efficient use of the
equipment.
WHAT'S INCLUDED
Underwater WiFi Cable and Accessories Case
The rugged waterproof case contains the following. We have also incorporated a number of slots in
the foam for storing of miscellaneous accessories such as USB power hubs, camera cables, etc.
Carbon Fibre Pole
1. 4K Action Camera
2. 2 x LumeCube lights and associated
mounting tray
3. Accessory slot - Power Hub or similar (not
included)
4. Accessory slot - AC power cable for
hub/tablet (not included)
5. USB Wall cubes (not included)
6. Ball socket arm
7. USB cables slot
8. Action camera spare battery and charger
9. Underwater WiFi cable
10.Tablet storage slot (tablet not included)
11.Telescopic Carbon Fibre Pole with
integrated articulating hinge.
12.Hard case.
Page 1 of 10
Rev1.1 | May 2018
Advertisement
Summary of Contents for CamDo UNDERWATER WIFI INSPECTION PACK
- Page 1 SETUP INSTRUCTIONS UNDERWATER WIFI INSPECTION PACK REV1.1 MAY 2018 INTRODUCTION Congratulations on your purchase of the high quality telescopic carbon fibre pole and underwater wifi cable pack. This document details the setup instructions for safe and efficient use of the ...
- Page 2 GETTING STARTED The system is simple to use. The following instructions are for the GoPro HERO4 series of cameras. Connect Underwater WiFi Cable to the GoPro housing 1. Remove the standard backdoor from the GoPro housing. The standard backdoor of the GoPro housing is removed by opening the backdoor fully and then pulling or rotating the ...
- Page 3 3. Place the GoPro inside the camera housing and close the backdoor using the latch for a waterproof seal. Mounting the LumeCube Lighting System 1. Connect the 2x LumeCube lights to the included mounting tray using the thread ends ...
- Page 4 3. Attach the GoPro Buckle Mount to the GoPro Housing using the thumbscrew. 4. Clip the buckle into the tray Page 4 of 10 Rev1.1 | May 2018 ...
- Page 5 Telescopic Pole & Underwater WiFi Cable 1. Mount the camera / lighting tray onto the end of the telescopic pole. There is a ball mount already installed on the pole end ready to accept the camera / lighting system. ...
- Page 6 3. Extend the pole to the length you need. Tether the underwater wifi cable at the hinge with the included tether. 4. Teather the Underwater WiFi Cable to the handle of the pole using the elastic velcro strap. ...
- Page 7 LumeCube Setup The LumeCube has 10 manual brightness settings that change in increments of 150 lumens. The brightest setting maxes out at 1500 lumens. On a full charge at maximum brightness, the LumeCube will last up to 30 minutes. At 50% brightness, your LumeCube will last 2 hours. Each LumeCube produces a 60º...
- Page 8 LumeCube Charging and Waterproofing The one and only piece you have to worry about is the waterproof screw cap located at the back of the unit. BEFORE you expose the LumeCube to water, ensure always ensure the screw cap is tightened completely.
- Page 9 Action Camera Setup The CamDo system is compatible with several different action cameras that use the the knuckle style mounting such as on a GoPro. The action camera must also be WiFi enabled to stream the footage being shot to the surface to your local tablet or smartphone. ...
- Page 10 5. Once your camera is connected, you will now see a low resolution live view from the camera. Tap the record button to start/stop recording in upto 4K resolution. 6. Once you have finished recording, the full resolution footage can be reviewed via the App. The files can also be downloaded by connecting the camera to a laptop/PC or placing the SD ...