Page 2
All rights reserved. No part of this documentation may be repro- duced in any form, without prior written consent of Essex Electron- ics, Inc. Essex Electronics shall not be liable for errors contained in this manual. The information in this document is subject to change without notice.
*The ERM contains a serial interface to connect a computer for program- ming (see page 13) and reading codes or to a printer for real-time print-out of activities. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
3. Second Door - Users can be assigned to open a 2nd door. 4. Doorbell - Press # at the Keypad to trigger a 1 second output for a doorbell (not included). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 8
4. Internal Alarm System - Detect Break-in, Door-ajar & Tamper. 5. Doorbell - Press # at the Keypad to trigger a 1 second output for a doorbell (not included). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Door Ajar Time setting. RED, BLACK, GREEN, VIOLET, GRAY, ORANGE and SHIELD- These wires all connect to the ERM module. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 10
When the CLOCK terminal is not grounded, only those codes with 24-hour Access Authorization (page 21) will function. The disabled codes are still considered valid and will not trigger Tamper Alarm if tried repeatedly. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
To change the illumination on the K1-26 only, enter the code as follows: Code Standby Mode Normal Operation 210 # Off (factory default) Off (factory default) 211 # 212 # Bright Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 12
2. Jumper the two pins above the connector labeled "CONFIG". 3. Apply appropriate power. (You should hear 4 beeps and the RED LED will flash and the GREEN LED will be solid). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 13
8. Re-apply power. 9. Press PROGRAM button in the ERM to establish the encoded connection. This will put the system into setup mode. 10. Press * * to exit. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Output as Aux.) to Turn Output A ON (2 Output as Aux.) to Turn Output B OFF (3 Output as1 Aux.) to Turn Output B ON (3 Output as Aux.) Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
If communication is lost for more than 2 seconds, the unit goes into LockUp Mode and can only be restored to Normal Operation by pressing the PROGRAM button. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 16
Since the output is on to indicate a Non-Alarm status when using Output B relay as an Alarm, a loss of communication or invalid EC will always create an alarm indication. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Serial COM Port. (The K1-ERM is set for 9600 baud.) ! ! ! ! ! Installing the CD-ROM Install the “KeypadUtils12.exe” from the enclosed CD. The files will default to C:/Program Files/Essex unless otherwise re-directed. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
User Number 1’s), you will be asked to select a resolution. Once complete, you will need to save the chart and upload to the Keypad to make sure they both agree. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Select “Options” and “COM Port.” Alarms Loss of power- reported when power is restored. Tamper Alarm- 4 incorrect code entries Loss of communication between Keypad and ERM (Keypad removed or broken connection). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
ERM board. This will take you to Step 3 of Programming System Setup. Once you enter setup mode, you have 30 seconds to begin the program sequence. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 21
Double Slow Flash Slow Flash Triple Slow Flash Solid Configuring Output A (Default: Aux #1) a. Enter b. Select one of the following: CCTV / External Light 1) Enter Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 22
Keypad Status After Step Completion Step Beep Red LED Green LED Double Slow Flash Slow Flash Double Slow Flash Fast Flash Triple Slow Flash Solid Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 23
Timed- Enter the desired time interval in hours (1-98), followed by Example: 5 # 3 # 5 # 9 9 # (Sets Second Door with 5 second Door Open Time and Manual Latching) Doorbell 1) Enter Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 24
Baud Rate to 9600 (default) 4. Enter to complete the sequence and reset the system to normal operation. Note: If using a printer or Hyper-terminal, will print Setup Configuration Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Latching Authorization Program or Delete Users Authorization Output A Authorization (see notes) 2nd Door (see notes) Output B Authorization (see notes) 3rd Door (see notes) 24-hour Access (see notes) Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 26
24 Hour Access requires an external time clock or keyswitch. This allows you to restrict access to Users who are not assigned 24-hour Access. See Time Clock Input on pages 5-6. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 27
Modify a User by User Code a. Enter b. Enter the User Code for the User you wish to modify, followed c. To change this User’s Code, enter the New User Code followed Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 28
If no more Users are to be deleted, enter and return to Step 3, or if you have completed all User Programming, enter second time to complete programming sequence and reset system to normal operation. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 29
Programming, enter a second time to complete programming sequence and reset system to normal operation. 4. Enter to complete the sequence and reset the system to normal operation. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 30
Steps 1 & 2 each time. However, if more than 30 seconds elapse between each step during programming, the system will reset and you will have to start from Step 1. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
If 4 invalid Master Codes are entered, the unit will go into Tamper mode. If you have set the Hyper-terminal to send CTRL+H, SPACE, CTRL+H for backspace, the backspace key will work correctly. All commands are case insensitive. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
List Keypad configuration Exit program *[,OPTIONS]= option numbers with no commas between them. Example: Type mo,5,555,13 to change User 5 code to 555 and give Latching and Output A authorization. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Act of God, or is misused, damaged by accident, Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 37
We also reserve the right to have our representative make any inspection or repairs, or furnish replacements. This warranty excludes elevator and vehicle Keyless Entry® Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 38
THIS WARRANTY MAY NOT BE EXPANDED OR EXTENDED BY ANY ORAL REPRESENTATION, WRITTEN SALES INFORMATION, ADVERTISING, DRAWINGS OR OTHERWISE. ESSEX ELECTRONICS, INCORPORATED IS NOT RESPONSIBLE HEREUNDER FOR INCIDENTAL DAMAGE TO Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
Page 39
All non-warranty repair freight charges are paid for by the customer. Non-warranty repair charges are returned COD. (Factory Authorized Distributors are subject to standard terms.) Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...