During Assembly - Palram Glory 8'x8' Manual

During Assembly
Make sure the
base is
square by measuring the diagonals and level by using
a
spirit level.
You
may
use
silicone lubricant spray
in
order to help you slide the
panels
into the profiles.
Do not spray the polycarbonate panels.
Use
a
rubber mallet if
necessary.
All panels
with
the stamped words
"THIS SIDE
OUT" must be facing out to create
full
UV
protection. Remove plastic sticker
as
panels
are
locked
in place.
When
encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
This icon indicates
that the installer should
be
inside the product.
This
icon indicates that
the installer should be
outside the product.
In
Attention
During assembly
use
a
soft surface below the parts to avoid scratches and damages.
Steps
Step 4:
Refers
only for the extension kit! The extension kit contains
a
base
connector, either part
#8447 or #7601
Step 11:
Please
make
sure
the screw connection
is
made exactly
as
illustrated.
A
-
Connect the screw
in
the left hole.
B -
Connect the screw in the right hole.
Step 13:
Peel
the film covering the
panel.
Make sure you install it with the
UV
protected
side
out.
Step 23: Side Louver
Window:
can be located only on one
of
the
two
central panels.
* If
you assemble the greenhouse with
an
extension module, the window
can be
placed on
all
panels,
except for the
last
two
end panels.
*
Note:
The selected placing will affect the next assembly steps.
Step 31:
It is
highly recommended to
paste
the sealing tape
at
the bottom edge of
panels 7903
+
7904
is
order to prevent moisture seepage.
Step 38:
Roof
window
can be
located only on one of the two central roof
panels.
* If you assemble the greenhouse
with
an extension module, the roof windows must be placed on
panels only
as
specified
in
the manual.
*
Note:
The selected placing will affect the next assembly steps.
Step 43:
Please
tighten
screws
from inside the greenhouse.
In
addition,
please
tighten the
remaining
loose screws.
Step 48:
As
mentioned at the
'Before Assembly' section,
prior to
fitting
the
Automatic
Vent Opener, the power-tube
has
to
be
cooled
by
placing it
in
a
refrigerator for
approximately
30 minutes.
Step 57: Door can be installed
as
a
left hand door or right hand
door
as
per your decision.
These
instructions show
a
right hand door
assembly. Please
determine door opening
direction.
This
decision will affect the next assembly
steps.
Step 59:
Please
adjust the hinges height
in
accordance
with
the upper post and lower ramp
of the door aperture,
as
specified
in
Level
C.
Step 63:Threading parts 7888 exactly
as
specified in Level
B, is
very
important
in
order to
create good drainage.
Step 67: Anchor the greenhouse on to
a
solid surface such
as
concrete or asphalt,
use
suitable screws and plugs. (Screws and plugs are not supplied).
* Please
tighten
all
screws
when completing assembly.
Screws 411
and nuts
412 & 466 are used
thruoghout the assembly
process.
Screws
411
are
to
be
assembled from the outside and nuts 412
& 466
from the inside of
the greenhouse.
Do
not fasten screws and nuts (411,412
&
466) more than 2-3 turns only.
Do
not tighten
them until completion of the panels'assembly, if not specified otherwise.
However,
in
some steps,
temporary tightening of
a
few screws may be needed to
prevent
a
profile from falling.
Note:
Firmly connect the product to
a
level surface immediately after completion of the
assembly.
Anchoring this product to the ground
is
essential to its
stability and rigidity.
It
is
required
to complete this stage in order for your warranty to be valid.