Advertisement
Quick Links
This manual describes the installation process for the ICU EVe charging point
for electric vehicles. Carefully read this manual before you install the charging
point. ICU Charging Equipment and Alfen bv cannot be held liable for any
consequential damage and/or losses that may arise from the use of this
manual. This manual applies to the product types below:
Plug & Charge
4457.230V.50HZ.16A.1FNPE.2X16A.PUAST
4457.400V.50HZ.32A.3FNPE.2X16A.PMAT
4457.400V.50HZ.16A.3FNPE.1X16A.PMAT
4457.400V.50HZ.64A.3FNPE.2X32A.PMAT
4457.400V.50HZ.32A.3FNPE.1X32A.PMAT
RFID + RFID Display
4457.400V.50HZ.32A.3FNPE.2X16A.RMAST
4457.400V.50HZ.16A.3FNPE.1X16A.RMAST
4457.400V.50HZ.64A.3FNPE.2X32A.RMAST
4457.400V.50HZ.32A.3FNPE.1X32A.RMAST
4457.230V.50HZ.16A.1FNPE.2X16A.DRUAST
4457.400V.50HZ.32A.3FNPE.2X16A.DRMAST
4457.400V.50HZ.16A.3FNPE.1X16A.DRMAST
4457.400V.50HZ.64A.3FNPE.2X32A.DRMAST
4457.400V.50HZ.32A.3FNPE.1X32A.DRMAST
The type number can be found on the identification label on the bottom side of
the product.
Safety
The electrical system must be dead (disconnected from the power
supply) during all installation and maintenance work.
Installation work must be performed by professionals who are familiar
with this manual and work based on the IEC-60364 regulations.
Work may not be performed when it is raining or the air humidity is higher
than 95%.
Never connect more than one charging object per group.
1
Advertisement
Related Manuals for ICU EVe
Summary of Contents for ICU EVe
- Page 1 This manual describes the installation process for the ICU EVe charging point for electric vehicles. Carefully read this manual before you install the charging point. ICU Charging Equipment and Alfen bv cannot be held liable for any consequential damage and/or losses that may arise from the use of this manual.
-
Page 2: Installation Requirements
Take the following requirements into consideration when installing the ICU EVe: The cable route of the main distributor to the ICU EVe must be protected against power surges and short-circuits by using a B characteristic circuit breaker or a screw gG tag fuse. - Page 3 Always carry out the wiring at the maximum charging current of the charging point with a continuous load. The cable thicknesses in this manual are indicative. The installer is always responsible for determining the correct cable thickness on site and the application of the applicable standards. Note: the requirements for the installation may depend on the location.
-
Page 4: Contents Of The Packaging
Contents of the packaging 1 ICU EVe base unit 1 ICU EVe front cover 1 wall bracket 2 anti-theft bolts 1 pin key hexagon socket wrench Not supplied accessories Tools Spirit level. (Impact) drill. Screwdriver for an M5 cross recess hole. - Page 5 Charging point installation Fold open the packaging to first remove the white front cover. The front cover is fixed to the charging unit with two screws on the top and bottom sides. Loosen the screws at the bottom using a hexagon socket wrench and loosen the two screws on the bottom side of the rear cover using M5 Torx (T25).
- Page 6 Insert the power supply cable through the opening in the screw connection. Pull the power supply cable into the housing approximately 150 mm. The power supply cable must be long enough to be pulled into the housing from the ground or wall. Fix the power supply cable in the screw connection by tightening it in such a way that there is no movement in the power supply cable.
- Page 7 12. Lower the front cover with the two protruding studs in the grooves on the top side that is indicated with the blue arrows (fig. 4). Figure 4 13. Tighten the screws at the top side of the base unit using M5 Torx. Figure 5: 3-phase model shown 14.
-
Page 8: Product Specifications
Commissioning Connect the power to the power supply cable. The EVe will show different LED indicators. Ultimately, the LED will switch off and the charging point will be ready for use. Take the following steps in case of an error message: Check the earthing connection. -
Page 9: Identification Label
The identification label specifies, for example, the model, production date and serial number. It can be found on the bottom side of the charging point. Always make reference to the serial number when writing to ICU so that you receive the fastest support.