Related Manuals for Sahaphan KW1000G-3
Summary of Contents for Sahaphan KW1000G-3
- Page 1 Waterproof Scale Operation Instruction WATERPROOF SCALE Operation Instruction Ver1.0...
-
Page 2: Table Of Contents
Waterproof Scale Operation Instruction Content I． BEFORE USING THE SCALE…………………..……….1 II. PREPARING TO USE THE SCALE………….………..….1 III. INTRODUCTION …………………………………..………1 IV. LCD DISPLAY SYMBOLS…………………………..……2 V. KEYBOARD FUNCTION……………………………..……3 VI. GENERAL ……………………..…..4 PARAMETER VII. CONNECTION OF INTERFACE…………......…..6 VIII. MEANS OF POWER SUPPLY & CHARGING…………7 IX. -
Page 3: I． Before Using The Scale
Waterproof Scale Operation Instruction I. BEFORE USING THE SCALE To enable you to use this scale correctly, we suggest you read this manual carefully. 1. Do not use scale in areas with excessive water and don’t spray the scale or indicator with water when cleaning. - Page 4 The scale will power off automatically without recharging after the low battery symbol shows upon for 20 to 30 hours on the display. As a recommendation, the scale should be fully recharged before using the scale again. 3.4 SPECIFICATIONS Model KW1000G-3 KW1000G-6 KW1000G-15 KW1000G-30 Capacity 3kg x 0.5g...
-
Page 5: Keyboard Function
Waterproof Scale Operation Instruction LED INDICATION SYMBOLS Indication DESCRIPTIONS Reading is stable. TARE There has tare weight in the scale ZERO The scale has been zero. HOLD Weighing is hold. Battery Capacity. Shining is charging. F /M / L Kg,lb,lb.oz,g,PCS Weighing unit HI, OK,LO Checking weighing... -
Page 6: General Parameter
Waterproof Scale Operation Instruction VI. GENERAL PARAMETER SETTING * Plug the circuit breaker JP1 into ‘off’, and the following operation can be performed. Press and hold [MODE] & [→0←] key for 3 seconds, the screen will display ====== . Press [MODE] to enter the menu. -
Page 7: Counting Function Operation
Waterproof Scale Operation Instruction if scale is under this weight, “ LO ” indication is shinning with alert buzzer. Press [►] & [▲] key to set the point weight, then press [ MODE ] to confirm and finish. For example: For one 30kg scale, desired weight is 10kg, deviation value is ±0.2kg. Pressing [►] &... - Page 8 Waterproof Scale Operation Instruction This mode is used to indicate the number of pieces of an item that placed on the pan. To ensure accuracy, the parts that counted must be consistent in weight. The scale uses a sampling method to determine the average pieces weight of the items that counted. For example, 30kg scale, sample weight is 200g, it is 100pcs sample units.
- Page 9 Waterproof Scale Operation Instruction Step 8: Offload the weight, reading “0.00kg ” will display and Zero indication will show denoting there is nothing being weighted on the scale. Step 9: The scale will return to weighing mode after calibration is finished. Attention: Do remember to switch the breaker into “OFF”...
- Page 10 Waterproof Scale Operation Instruction 5-2. Output data The screen displays AdS- r X . X values from 0-3 that decide output data of serial protocol to computer.User can demand a customize serial protocol. X=0. It is the standard data, It is Displayed weight, Gross weight, Net weight,Tare weight with ASCII code. X=1-3, it is customize data.
-
Page 11: Error Signal
Waterproof Scale Operation Instruction X=1~9, the display weight is hold while it is stable and keep 1~9seconds. 7.3 Refresh mode The screen displays “FLt2. X ” . It is the refresh mode after hold function while set “Flt0 =1”. X=0, when unload the weight until it less than 20d, holding is canceled and weight is refreshed. Y=1~9, when weight is on holding status, the holding will be canceled automatic after preset seconds and refresh and hold a new weight.
Need help?
Do you have a question about the KW1000G-3 and is the answer not in the manual?
Questions and answers