Lesco 020092 Parts List And Instructions Manual

Lesco 020092 Parts List And Instructions Manual

Rotary spreader optional equipment calibration

Advertisement

020092/Epoxy, 020093/Stainless Steel, 704355
80 LB Rotary Spreader
Optional Equipment
Calibration
Parts List AND INSTRUCTIONS
Starting Date: 10/01
Starting Date: 10/01
Starting Date: 10/01
Starting Date: 10/01
Starting Date: 10/01
4:1 Gearbox x x x x
4:1 Gearbo
4:1 Gearbo
4:1 Gearbo
4:1 Gearbo

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 020092 and is the answer not in the manual?

Questions and answers

J. Scaramuzzo
May 23, 2025

Looking for the part that connects the cable (one of three on 80 lb Lesco spreader) to the outside right handle. This cable engages the agitator. Lesco SPDR 80 Commercial Plus. Appears newer models are one lever/handle only.

1 comments:
Mr. Anderson
May 25, 2025

The part that connects the cable to the outside right handle on the Lesco SPDR 80 Commercial Plus spreader is the "on/off bracket."

This answer is automatically generated

Summary of Contents for Lesco 020092

  • Page 1 Starting Date: 10/01 Starting Date: 10/01 Starting Date: 10/01 Starting Date: 10/01 4:1 Gearbo 4:1 Gearbo 4:1 Gearbox x x x x 4:1 Gearbo 4:1 Gearbo 020092/Epoxy, 020093/Stainless Steel, 704355 80 LB Rotary Spreader Optional Equipment Calibration PARTS LIST AND INSTRUCTIONS...
  • Page 2 Rotary Spreaders — Parts List The Optional Jet-Action Deflector Part No. 060087 Parts List Ref.LESCO Description Used 70 061064 SS Handle ..... 1 71 061065 SS Bracket ....1 72 061066 Deflector ....... 1 73 061053 SS Washer ....1 74 061052 SS Cotter Pin ....
  • Page 3 68 020492 Slide Lever ............1 original frames. See Note C above.) ....1 706895 “Lesco” Decal ..........1 21 060031 Clevis Pin, 1/4" x 1/2", SS ......1 70 060021 Pinion Gear ............ 1 22 060032 Cotter Pin, 3/32 x 1/2, SS .......
  • Page 4 The Optional Remote Deflector — Part No. 035591 Parts List Mounting Instructions Ref. Item 1.Remove the right rear bolt holding the hopper to the frame but save No.No. Description Used the nut. Install a 1/4-20 x 2" pan head machine screw (Ref. 14), the rubber pad (Ref.
  • Page 5 The Optional Remote 3rd Hole Slide — Part No. 030571 Mounting Instructions Parts List Ref. Item 1. Drilll a 9/32" hole in the upper handle assembly as shown Description Used in the sketch on the opposite page. 1 030418 Bracket, Dual Lever ........1 2.
  • Page 6 8. Place the handle grips on the handles. 9. Grease the axle bearings and the gear support. 10. Read the LESCO Spreader Calibration instructions packed with your spreader and calibrate following the instructions.
  • Page 7 “S” position. Open the operating lever and insert the even numbered Check the spreader discharge holes with the operating lever in the LESCO Calibration Gauge into one of the open holes in the hopper closed position. If the discharge holes are not fully closed, thread the bottom.
  • Page 8 Equipment to conform to specifications or a defect in material or workmanship, they must promptly notify LESCO in writing of such claim. Any claims under this warranty must be received in writing by LESCO within 13 months from the date of original delivery.

This manual is also suitable for:

020093704355

Table of Contents

Save PDF