Related Manuals for Hogtunes WILD BOAR AUDIO WBA ULTRA KIT “SE”
Summary of Contents for Hogtunes WILD BOAR AUDIO WBA ULTRA KIT “SE”
- Page 1 WBA ultRA Kit “ SE ” i nSt All At i o n m Anu Al IMPORTANT! A radio “Re-Flash” is required to make this system perform correctly. Please read manual for more information.
- Page 2 Model Ultra Classics. We want your new kit to work as well as it was designed to, so if you have any questions or concerns, please email: tech@hogtunes.com or call us during regular business hours at 705-719-6361 (EST). If you still need help, please consider a professional installation by your dealer.
-
Page 3: Before Getting Started
beFORe geTTINg sTARTed The amp in this kit (WBA 600.4) is rated to produce 150 watts x 4 using the supplied 4 ohm Wild Boar speakers. As explained throughout this manual, the required radio flash is referred to as “4 speaker no amp” which is the factory flash on non CVO Ultra/Ultra Trike models. -
Page 4: Step #1: Getting Started
se ct io n 1 fR ont S pEA KER inS t A ll At io n Step #1: Getting Started Remove the bike’s seat, and undo the main (+ and -) connectors from the battery. Remove the outer fairing/headlamp assembly and set aside. Refer to a service manual if you need help with this. - Page 5 and carefully take off each speaker wire by un-doing one at a time. Take a Wild Boar Audio speaker and attach the speaker wires noting the factory speaker wire connectors will lock into place on the speaker. Sit the Wild Boar Audio speaker into the cabinet noting the speaker MUST be oriented so that the wires are in the bottom (6 o’clock) position so the speaker frame will not touch the small locater peg that sticks out from the face of the cabinet.
-
Page 6: Amplifier Installation
sec tio n 3 A m pli fi E R i n S t A llA t i on Step #1: On the side of the factory amplifier, you will see a large multi-pin connector that needs to be unplugged from the amplifier. Remove the factory amplifier and its mounting plate from the bike. - Page 7 Step #3: Take one amp, and make sure its “Radio Flash Selector Switch” on the side of the amp is set to position “A”. In the same orientation as it came out of the box, “stick” the amp to the left half of the plate so the power harness is closest to the back of the radio.
- Page 8 Routing thE poWER And REAR hARnESS Step #1: The power/ground and rear harness will pass through the inner fairing where the main wire harness passes through on the brake side of the bike. If your comfortable removing and re-installing the fuel tank, the wires can go in the factory wire “chase”.
- Page 9 Step #4: Attach the amp’s red wire to the positive (+) battery terminal and the amp’s brown wire to the negative (-) battery terminal. The factory battery wires are also re-installed at this point. When attaching the power and ground wires, it is always a good practice to do the negative first. When the positive connector touches the battery, some sparking is normal.
- Page 10 sec tio n 4 fin Al Sy St E m A d j u St mE nt This section is VITAL to the correct operation of the system, please make sure you read and understand it, or contact us! • This kit has been designed to give great sound with the radio bass and treble controls in the middle position.
- Page 11 Please contact Hogtunes head office for all warranty claims. Products found to be defective during the warranty period will be repaired or replaced (with a product deemed to be equivalent) at Hogtunes sole discretion. Hogtunes/Wild Boar Audio’s complete warranty policy is available on our website at www.wildboaraudio.com...
- Page 12 Original Equipment, which can be a distraction to the rider and/or passenger. Please use caution when adjusting or playing your stereo at high volume, especially in traffic. You are a valued customer so please: Ride Alert Arrive Alive! www.wildboaraudio.com www.hogtunes.com...
Need help?
Do you have a question about the WILD BOAR AUDIO WBA ULTRA KIT “SE” and is the answer not in the manual?
Questions and answers