Subscribe to Our Youtube Channel
Related Manuals for Gemalto Cinterion EMS31
Summary of Contents for Gemalto Cinterion EMS31
- Page 1 ® Getting Started with Cinterion EMS31 User Guide Version: 01b DocId: EMS31_startup_guide_v01b GEMALTO.COM/M2M...
- Page 2 Copyright © 2017, Gemalto M2M GmbH, a Gemalto Company Trademark Notice Gemalto, the Gemalto logo, are trademarks and service marks of Gemalto and are registered in certain countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corpora- tion in the United States and/or other countries.
-
Page 3: Table Of Contents
® Getting Started with Cinterion EMS31 Page 3 of 17 Contents Contents Document History ...................... 4 Introduction ......................... 5 Supported Products ................... 6 Related Documents ................... 6 Getting Started with EMS31 ..................7 Technical Requirements for Using EMS31 Modules ......... 7 Connecting the EMS31 Evaluation Module to the DSB75 ......... -
Page 4: Document History
® Getting Started with Cinterion EMS31 Page 4 of 17 0 Document History Document History ® Preceding document: "Getting Started with Cinterion EMS31" Version 01a ® New document: "Getting Started with Cinterion EMS31" Version 01b Chapter What is new Replaced circuit diagrams. ®... -
Page 5: Introduction
Note: The hardware components listed above as part of a development and test environment are also mentioned in as part of the comprehensive reference equipment used by Gemalto M2M for type approval. For general development and test purposes however, there is alterna-... -
Page 6: Supported Products
® Getting Started with Cinterion EMS31 Page 6 of 17 1.1 Supported Products Supported Products This document applies to the following Gemalto M2M modules: ® • Cinterion EMS31-V Module ® • Cinterion EMS31-US Module EMS31 in this document refers to all of the above mentioned product variants. Where neces- sary a note is made to differentiate between these product variants. -
Page 7: Getting Started With Ems31
EMS31 evaluation module (not supplied by Gemalto M2M) - RS-232/USB converters and USB cables or Serial-to-USB cables for the module's asyn- chronous serial interfaces ASC0 and ASC1 (not supplied by Gemalto M2M). • Appropriate application for controlling the module from within a PC’s operating system. For Windows, e.g. -
Page 8: Connecting The Ems31 Evaluation Module To The Dsb75
® Getting Started with Cinterion EMS31 Page 8 of 17 2.2 Connecting the EMS31 Evaluation Module to the DSB75 Connecting the EMS31 Evaluation Module to the DSB75 To properly connect the EMS31 evaluation module and all accessories to the DSB75 please complete the steps listed below. - Page 9 ® Getting Started with Cinterion EMS31 Page 9 of 17 2.2 Connecting the EMS31 Evaluation Module to the DSB75 X201 X205 X202 X110 X401 X400 1 4 2 3 X 203 X120 S112 X121 DSB75 S467 S464 S453 S110 S 463 S462 S 452 S 457...
- Page 10 ® Getting Started with Cinterion EMS31 Page 10 of 17 2.2 Connecting the EMS31 Evaluation Module to the DSB75 RS-232 cable at RS-232 cable at Power supply (X400/X401) COM2 (X202) for COM1 (X201) for ASC1 ASC0 Antenna cable U.FL connector (X391) linking U.FL for main antenna antenna connector...
-
Page 11: Start Up The Module
® Getting Started with Cinterion EMS31 Page 11 of 17 2.3 Start Up the Module Start Up the Module After connecting the EMS31 evaluation module to the DSB75 as described in Section 2.2, the module can be switched on. Note: ASC0 serial interface is set as a default interface for firm- ware upgrade and AT commands execution. -
Page 12: Appendix: Ah6-Dsb75 Adapter
® Getting Started with Cinterion EMS31 Page 12 of 17 3 Appendix: AH6-DSB75 Adapter Appendix: AH6-DSB75 Adapter The EMS31 Evaluation Module connects to the 80-pin board-to-board connector X120 on top of the AH6-DSB75 Adapter. The 2x40-pin header X101/X102 of the DSB75 Support Board connects to the 80-pin female connector X135 located on the back of the AH6-DSB75 Adapter. - Page 13 ® Getting Started with Cinterion EMS31 Page 13 of 17 3 Appendix: AH6-DSB75 Adapter X135 Marking: “AH6-DSB75 X305 Adapter” ADC1_AD X320 X321 X322 ADC2_AD VEXT BATT+ Pogo AGND pins VMIC BIAS1 X317 X318 X319 X308 X309 MICN1 BIAS2 SMP. X323 X350 X324 X325...
-
Page 14: Appendix: Circuit Diagrams For Evaluation Module Board
® Getting Started with Cinterion EMS31 Page 14 of 17 4 Appendix: Circuit Diagrams for Evaluation Module Board Appendix: Circuit Diagrams for Evaluation Module Board LGA FOOTPRINT X 1 0 0 R136 GPIO11 R138 GPIO12 VSIM_I VSIM R102 R114 EMERG_RST CTS1 RTS1 TP110... - Page 15 ® Getting Started with Cinterion EMS31 Page 15 of 17 4 Appendix: Circuit Diagrams for Evaluation Module Board BATT+_DSB ESDA6V1-5P6 X201 2 2 p CCIN CCCLK 120R C200 V180 VSIM R290 L 2 0 2 CCRST CCIO R234 RING0 R235 R259 V200 DSR0...
- Page 16 ® Getting Started with Cinterion EMS31 Page 16 of 17 4 Appendix: Circuit Diagrams for Evaluation Module Board TP301 TP302 R310 BATT+_DSB BATT_PWR BATT_PWR Figure 8: Schematic sheet 3 EMS31_startup_guide_v01b 2017-10-19 Confidential / Released...
- Page 17 About Gemalto Since 1996, Gemalto has been pioneering groundbreaking M2M and IoT products that keep our customers on the leading edge of innovation. ® We work closely with global mobile network operators to ensure that Cinterion modules evolve in sync with wireless networks, providing a seamless migration path to protect your IoT technology investment.
Need help?
Do you have a question about the Cinterion EMS31 and is the answer not in the manual?
Questions and answers