Page 3
CM17202 PC/104-Plus Fast Ethernet Controller utilityModule User’s Manual RTD Embedded Technologies, INC. 103 Innovation Blvd. State College, PA 16803-0906 Phone: +1-814-234-8087 FAX: +1-814-234-5218 E-mail sales@rtd.com techsupport@rtd.com web site http://www.rtd.com...
Page 5
All rights reserved Printed in U.S.A. The RTD Logo is a registered trademark of RTD Embedded Technologies. cpuModule and utilityModule are trademarks of RTD Embedded Technologies. PhoenixPICO and PheonixPICO BIOS are trademarks of Phoenix Technologies Ltd. PS/2, PC/XT, PC/AT and IBM are trademarks of International Business Machines Inc. MS- DOS, Windows, Windows 95, Windows 98 and Windows NT are trademarks of Microsoft Corp.
Table of Contents CHAPTER 1 INTRODUCTION .........................1 ...........................1 LECTRICAL PECIFICATIONS ..........................1 ECHANICAL PECIFICATIONS ..............................2 NVIRONMENTAL ................................2 OFTWARE CHAPTER 2 CM17202 LAYOUT ......................3 ..........................3 INDING ONNECTORS ............................3 OMPONENT OCATIONS ........................4 IST OF ONNECTORS AND WITCHES PC/104 B , CN1 CN2 ......................5...
Page 7
Table of Figures 1: C ..........................3 IGURE OMPONENT OCATIONS 2: RJ-45 J ..........................10 IGURE ONNECTOR 3: PCI S ......................13 IGURE ELECTOR OTARY WITCH Table of Tables 1: L ......................4 ABLE IST OF ONNECTORS AND WITCHES 2: PC/104 XT B ........................5 ABLE ONNECTOR 3: PC/104 AT B...
NTRODUCTION Chapter 1 • This manual gives information on the CM17202 PC/104-Plus Fast Ethernet Controller utilityModule. This module provides a twisted-pair 100 Mbit ethernet connection to support the Real Time Devices’ PC/104-Plus cpuModules and other PC/104-Plus processor modules. Features The following are major features of the CM17202 utilityModule.
Non-Condensing Relative Humidity: < 95% at 40°C WARNING! Like all equipment using CMOS devices, the CM17202 must be protected from static discharge. Never touch any of the parts except at static-free workstation. Use anti- static bag shipped with the CM17202 to handle the board Software The 21143-TD is supported by DOS, Windows 3.1, Windows 95, Windows NT, Windows 2000,...
PC/104 bus. These keying pins are a part of the PC/104 standard, and we strongly recommend you leave them in place. If you have other modules without keying pins, we suggest you modify them to include keying. CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
5.0V I/O signals and Pin-D30 will be modified in the same manner for 3.3V I/O. It is recommended that both KEY pins (A1 and D30) be electrically connected to GND for shielding. CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
GNT* -- Grant indicates to the requesting device that access has been granted. System CLK -- Clock provides timing for all transactions on the PCI bus. RST* -- Reset is used to bring PCI-specific registers to a known state. CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
Page 16
+12V -- +12 volt supply -12V -- -12 volt supply +3.3V -- +3.3 volt supply VIO -- This signal typically is the I/O power to the bus drivers on a PCI bus card. CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
The RJ45 connector exceeds the height limit of the PC/104 specifications. The optional CN5 connector is also a 10/100Base-TX connection and can be factory installed if the RJ45 connector height is a problem CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
Transmit + Receive - Transmit - N.C. Not connected Receive + N.C. Not connected N.C. Reserved N.C. Not connected N.C. Not connected N.C. Not connected Table 6: CN5 Signal Assignments CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
Transmit Clock TXEN Transmit Enable TXD0 Transmit Data 0 TXD1 Transmit Data 1 TXD2 Transmit Data 2 TXD3 Transmit Data 3 Collision Detect Carrier Sense Table 7: MII Interface Connector Layout CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
PC/104-Plus or PCI-104 stack. To do this, you will connect the PCI and/or ISA bus connectors on the CM17202 to the respective connectors of your stack. Before you can use this module you have to set the PCI board selector rotary switch located on the module (SW1).
ODULE Chapter 3 WARNING! Like all equipment using CMOS devices, the CM17202 must be protected from static discharge. Never touch any of the parts except at static-free workstation. Use anti-static bag shipped with the CM17202 to handle the board The following sections contain information on configuring the CM17202 PC/104-Plus Fast Ethernet Controller utilityModule.
JP3, and JP4 to the 2-3 position and JP2 to the 1-2 position. Likewise, the user must set Jumpers JP1, JP2, JP3, and JP4 to the 1-2 position to use the RJ45 Connector. CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
Carefully package the product, using proper anti-static packaging. Write the RMA number in large (1") letters on the outside of the package. Return the package to: RTD Embedded Technologies, Inc. 103 Innovation Blvd. State College PA 16803-0906 CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
RTD Embedded Technologies, INC. This warranty is limited to the original purchaser of product and is not transferable. During the one year warranty period, RTD Embedded Technologies will repair or replace, at its option, any defective products or parts at no additional charge, provided that the product is returned, shipping prepaid, to RTD Embedded Technologies.
Page 25
RTD Embedded Technologies, Inc. 103 Innovation Blvd. State College PA 16803-0906 Our website: www.rtd.com CM17202 Fast Ethernet Controller utilityModule RTD Embedded Technologies, Inc.
Need help?
Do you have a question about the CM17202 and is the answer not in the manual?
Questions and answers