General Information - Novy Flat'Line 7640 Operating And Installation Instructions

GENERAL INFORMATION

General
These are the mounting instructions for the Novy hood shown on the cover. The manual is a separate booklet that has
been supplied with this hood. Carefully read these instructions before installing and commissioning the wall-mounted
chimney hood. It is recommended to have one or more qualified persons carry out the installation only.
Carefully take the hood from the packaging.
The hood is to be used above a cooking plate and/or domino and intended for household use only.
Important before mounting
Page 2 of these mounting instructions show the mounting drawings. Observe the following mounting tips before starting
the mounting activities:
• For easier mounting of the chimney hood, it is recommended to do this with at least 2 persons.
• Check if all mounting materials have been supplied using the drawing on page 2.
• Position the wall socket in the mounting frame such, that it is behind the shaft of the island chimney hood.
• Make sure that the wall has sufficient load bearing capacity.
• Remove the protective film from the stainless steel of the island chimney hood or shafts before mounting. Avoid
damaging the stainless steel.
Exhaust or recirculation
Before starting any mounting activities, you must have made the choice whether you are going to make an exhaust duct
to the outside or you are going to use the island chimney hood as a recirculation hood. If you choose for recirculation,
Novy offers the recirculation kit with item number 7640.400.
INSTALLATION
Follow with mounting drawings on page 2.
First measure the distance between the work surface and the ceiling (A). Choose the height between the bottom of
1
the chimney hood and the worktop (B) as follows:
• gas: min. 65 cm and max. 80 cm
• induction: min. 75 cm and max. 80 cm
• other cooking plates: min. 65 cm and max. 80 cm
Now the distance C has been determined and it is set with the help of the suspension frame of the island chimney
hood.
The distance C is set by sliding the suspension frame of the island chimney hood. As soon as the chosen height has
2
been set, the frame can be fastened using 4 bolts (906133). Firmly tighten the bolts.
Only when mounting an extension chimney
3
Demount the suspensionframe of the cookerhood by loosening the 4 bolts that keep the frame fixed to the cookerhood.
Mount the larger suspensionframe by sliding it into the cookerhood. Set the distance C as shown on the image and
fix the frame to the cookerhood by turning the bolts.
Place the cookerhood carefully on its side, open the underplate and take the grease filter out of the hood like shown
on the image. Turn the 6 outer screws loose and shove the 2 chimney pieces off the hood. Place the 2 new chimney
pieces onto the cookerhood and fasten the 6 screws again.
The drilling jig is supplied with these mounting instructions. Position the drilling jig against the ceiling into the correct
4
direction (see the indication for operation) at the place where the island chimney hood is to be mounted. Mark the
fastening holes on the ceiling. Drill the holes with a 8 mm bit. Insert the 4 plugs (906155) supplied. Take the ceiling
frame and the screws (906143) and fasten the ceiling frame onto the ceiling.
Pick up the chimney hood with at least 2 persons and lift it towards the ceiling frame. Press the suspension frame into
5
the ceiling frame until you hear a 'click'. Partly screw the 4 bolts (906133) into both frames. Level the island chimney
hood and then firmly tighten the 4 bolts.
Place the exhaust pipe on a connection nozzle of the motor using aluminium tape or a hose clamp. If you use a fixed
6
pipe, first place the supplied draught strip on the edge of the blow-off nozzle of the motor. Put the plug into the wall
socket.
Slide up the internal shaft part unto the ceiling. Do this carefully in order to prevent the chimney hood or the shafts
7
from being damaged. Fasten them with the 2 stainless steel screws (906035).
EN 7