Advertisement
Quick Links
Description
Package Contents
Before You Begin
Replacing the PanelView
1400e Keypad Faceplate
(Catalog Number 2711E-NK5)
(For PanelView Terminals 2711E-K14C6,
2711E-K14C7, 2711E-K14C15)
This document provides instructions for replacing the
PanelView 1400e terminal's keypad faceplate.
The keypad faceplate should be replaced by a qualified technician
who has experience in the service and repair of solid state
equipment. In no event will Allen-Bradley Company be responsible
or liable for indirect or consequential damages resulting from the
replacement of this part.
This kit includes:
•
keypad faceplate with controller
•
6 keypad faceplate mounting screws with washers
•
18 terminal mounting nuts and washers
Tools Required:
•
No. 2 Phillips screwdriver with a long shaft
•
Torque wrench capable of 27 inch-pounds torque
•
Torque wrench capable of 15 inch-pounds torque
•
Removeable thread locker (Loctite 242, Part Number 24221)
•
Torx T-15 driver
•
Wood block to elevate terminal keypad faceplate
Save Your Terminal Configuration and Application File
Before opening the terminal, write down the terminal's settings
(serial port, audio response, and screen saver configuration). If you
have no disk copy of the application file (as it was created in
PanelBuilder), upload the application file to a computer running
PanelBuilder and save the file on disk.
Installation Data Sheet
Advertisement
Related Manuals for Rockwell Automation Allen-Bradley 2711E-NK5
Summary of Contents for Rockwell Automation Allen-Bradley 2711E-NK5
- Page 1 Installation Data Sheet Replacing the PanelView 1400e Keypad Faceplate (Catalog Number 2711E-NK5) (For PanelView Terminals 2711E-K14C6, 2711E-K14C7, 2711E-K14C15) Description This document provides instructions for replacing the PanelView 1400e terminal’s keypad faceplate. The keypad faceplate should be replaced by a qualified technician who has experience in the service and repair of solid state equipment.
- Page 2 Replacing the PanelView 1400e Keypad Faceplate Precautions ATTENTION: To replace the keypad faceplate, you will need to put the unit face down gently onto a clean, soft protective surface. Be careful not to jar the unit. Permanent CRT damage can result. ATTENTION: Ensure that the PanelView terminal’s power cord is disconnected and that all cables have been disconnected from the rear of the terminal.
- Page 3 Replacing the PanelView 1400e Keypad Faceplate Step 2. Removing the To remove the keypad faceplate: Keypad Faceplate 1. Place the terminal face down on a protective surface. 2. Use a Torx T-15 driver to remove the two small black screws holding the cover plate on the left side of the keypad faceplate.
- Page 4 Replacing the PanelView 1400e Keypad Faceplate 4. Disconnect the cable from the controller board on the keypad faceplate. Note the position and orientation of the cable so that you can reconnect it properly. 5. The keypad faceplate is attached to the terminal by six Phillips screws, three on each side.
- Page 5 Replacing the PanelView 1400e Keypad Faceplate 7. Gently pull the keypad faceplate away from the unit at the top. Step 3. Preparing the New To prepare the new keypad faceplate: Keypad Faceplate Important: Prepare the new keypad faceplate in a dust-free environment.
- Page 6 Replacing the PanelView 1400e Keypad Faceplate Pull gently on the blue tabs to remove the legend key inserts from the old keypad faceplate and the new legend key inserts from the replacement keypad faceplate. Carefully insert the customized legend inserts from your old faceplate into your replacement faceplate.
- Page 7 Replacing the PanelView 1400e Keypad Faceplate 4. Holding the faceplate in position with one hand, start the middle screw on one side of the faceplate. Tighten it “finger-tight”, that is, as tight as you can by hand. Important: Start these screws very carefully, either by hand or with a screwdriver;...
- Page 8 Replacing the PanelView 1400e Keypad Faceplate 7. Start the remaining screws around the outside of the terminal. 8. Use the torque wrench to tighten them to a torque of 27 inch-pounds. 9. Connect the cable to P1 on the controller board of the new keypad faceplate.
- Page 9 Replacing the PanelView 1400e Keypad Faceplate Step 5. Remounting and To remount and reconnect the terminal: Reconnecting 1. Remount the terminal in its rack or panel. Secure the 18 nuts and washers, provided in the kit, to terminal mounting studs. Terminal mounting nut torque should not exceed 10 inch-pounds.
- Page 10 Replacing the PanelView 1400e Keypad Faceplate Test each key by pressing it. If the key is working, the corresponding key will appear to be pressed on the screen. F21 is the exit button. If you find any keys difficult to activate or inoperable, recheck the keypad cable connections for J5 on the logic board and P1 on the keypad controller board.
- Page 11 Rockwell Automation Headquarters, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414 382-2000 Fax: (1) 414 382-4444 Rockwell Automation European Headquarters, Avenue Hermann Debroux, 46, 1160 Brussels, Belgium, Tel: (32) 2 663 06 00, Fax: (32) 2 663 06 40 Rockwell Automation Asia Pacific Headquarters, 27/F Citicorp Centre, 18 Whitfield Road, Causeway Bay, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846 World Wide Web: http://www.ab.com...