Advertisement
ASSEMBLY INSTRUCTIONS FOR TREE STAND
1.
Tree stand consists of a
metal stand and a single
eye bolt. (See Fig.1)
Fig.1
3.
Insert an eye bolt and
screw into the hole. (See
Fig.3)
Fig. 3
ASSEMBLY INSTRUCTIONS FOR TREE
1.
Before you start to assemble the tree, choose an appropriate location near an outlet.
2.
Assemble the tree from the bottom to the top. Assemble tree stand according to the assembly
instruction for the tree stand.
3.
Carefully insert bottom section (C) of tree into the assembled tree stand and tighten the screw. (See Fig.1)
4.
Insert the middle section (B) of the tree into the bottom section (C). If the lights don't light up, rotate the
middle section (B) on right or left direction until it falls into place, then insert vertically and tightly into the bottom
section (C) to ensure proper circuit connection. (See Fig. 2)
2.
Open the stand to a 90 degree
angle until the hole lines up with
the hole on the tube. (See Fig.2)
Fig. 2
4.
Insert the tree into the stand and
adjust accordingly. The tree
should be straight and balanced
correctly. (See Fig.4)
Fig. 4
1
5.
Insert top section (A) into the middle section (B). If the lights don't light up, rotate the top section (A) on right or
left direction until it falls into place, then insert vertically and tightly into the middle section (B) to ensure proper
circuit connection. (See Fig. 3)
Note：There is an end connector on the top section (A), which is connected for tree top only.
6. Connect the end connector of green power cord with foot pedal switch (E) with the green connector
fixed on the bottom section (C)in correct direction (always match the protuberance on the end
connector of power cord to the protuberance on the green connector fixed on the bottom section (C)
according to the magnified drawing. (See Fig. 4).
7. Connect the end connector of white connector power cord (F) with the white connector fixed on the
bottom section (C)in correct direction (always match the protuberance on the end connector of
power cord to the protuberance on the white connector fixed on the bottom section (C) according to
the magnified drawing. (See Fig. 4).
8. Open all the branches (see Fig. 5).
9. Shape the branches. Start with tips farthest from the trunk, one to the right; one to the left and one
at the center of the main stem (see Fig. 6).
10. Plug the green power cord with foot pedal switch (F) into a proper outlet. (see Fig. 8). This tree
comes with a foot pedal switch with timer function for easy illumination and changing functions.
Please see below instructions of how to use the foot pedal switch.
11. Plug the white power cord (F) into a proper outlet. (see Fig. 7). The white connector power cord
plug is for tree top only.
HOW TO USE THE FOOT PEDAL SWITCH:
1. Press the foot pedal less than two seconds and release to select below 8 light functions:
1)
Steady on Warm white
2)
Flashing Warm White
3)
Slow Fade Warm White
4)
Steady Multicolor
5)
Flashing Multicolor
6)
Slow Fade Multicolor
7)
Sequential Multicolor & Warm White
8)
Slow Fade Multicolor & Warm White
2. Press the foot pedal more than two seconds to select below timer hours:
1) Indicator lights on foot pedal switch turn on red: the lights on tree will automatically be ON for 6
hours and be OFF for 18 hours. This cycle will occur every day unless the red indicator lights turn
out.
2) Indicator lights on foot pedal switch turn on green: the lights on tree will automatically be ON for 8
hours and be OFF for 16 hours. This cycle will occur every day unless the green indicator lights turn
out.
3) Indicator lights on foot pedal switch turn on blue: the lights on will automatically be ON for 2 hours
and be OFF for 22 hours. This cycle will occur every day unless the green indicator lights turn out.
4) Indicator lights on foot pedal switch turn on yellow: the lights will automatically be ON for 4 hours
and be OFF for 20 hours. This cycle will occur every day unless the yellow indicator lights turn out.
TROUBLE SHOOTING (If Lights Do Not Work):
1. If entire tree does not light, make sure connectors of power cord plugs (E, F) are securely
connected to the connectors fixed on the bottom section (C) and the power cord plugs are
securely inserted into a working electrical outlet.
2. Check whether all bulbs are tightly fixed inside the lamp holder.
3. If a bulb is blown or broken, replace the faulty bulb according to bulb replacement instructions
below.
4. If the fuse in the power cord plugs are blown, replace the blown fuse according to fuse
replacement instructions below.
5. If you are still experiencing problems with your tree, please contact our customer service
representative at 866-210-5958.
2
Advertisement
