Table of Contents
Advertisement
Quick Links
Model 200 / 250 / 260
Programming Guide
E-SEEK Inc.
R & D Center
9471 Ridgehaven Court #E
San Diego, CA 92123
Tel: 858-495-1900
Fax: 858-495-1901
Sales & Marketing
245 Fischer Ave #D5
Costa Mesa, CA 92626
Tel: 714-545-3316
Fax: 714-545-3595
www.e-seek.com
Last Revised by April 1, 2011
Rev: S04F
- 1 -
Advertisement
Table of Contents
Related Manuals for E-Seek 200
Summary of Contents for E-Seek 200
- Page 1 Model 200 / 250 / 260 Programming Guide E-SEEK Inc. R & D Center 9471 Ridgehaven Court #E San Diego, CA 92123 Tel: 858-495-1900 Fax: 858-495-1901 Sales & Marketing 245 Fischer Ave #D5 Costa Mesa, CA 92626 Tel: 714-545-3316 Fax: 714-545-3595 www.e-seek.com...
- Page 2 - 2 -...
- Page 3 This Programming Specification may be revised or withdrawn at any time. All rights reserved. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. - 3 -...
- Page 4 Serial Programming Specifications Serial Command Structure “Start Character”<Command 1>…<Command n>“End Character” The command structure consists of: Start character Command/s End character Start Character Every serial programming starts with an SOH character (ASCII value 01). The SOH character is needed only once for each set of commands, for example if you need to send two consecutive commands, it would require one SOH character followed by the two commands and the End character.
- Page 5 Factory Setup Description: To restore all factory settings, this command will overwrite all existing setting with the factory default settings. Scanner Response: ACK if the factory restore is completed successfully / NAK Description Field Values allowed Factory Default Default FACDEF=1 Table 1.1 Scanner Settings Description: To request current setting parameters (SETPAR), scanner model number...
- Page 6 Serial Number Read & Setup Description: The maximum length is 30 characters and no control character is allowed for a serial number. Example: „SOH‟<SERIAL:>„EOT‟ Scanner Response: ACK “XXXXXXXXXX…\r\n” / NAK X is a printable ASCII, with variable length Description: When this option is enabled the data will be sent before the decoded data. The default is a „disable‟.
-
Page 7: Serial Port Setup
Serial Port Setup Description: To setup serial port parameters, changes will be effective after scanner ACK response. Host Requirement: The Character Delay range is between 0 ms – 50 ms Scanner Response: ACK / NAK Description Field Values allowed RS232 Data Bits RSBITS=8 RSBITS=7 RS232 Parity... -
Page 8: Speaker Setup
Registration Key Read & Write Description: To setup Registration Key, changes will be effective after scanner ACK response. Control characters are not permitted. The maximum length is 30 characters*. When the REGIEN option is enabled, the data will be added between serial number and decoded data. - Page 9 Prefix / Suffix Setup Description: To setup prefix and suffix parameters, changes will be effective after scanner ACK response. Host Requirement: To setup prefix and suffix with a control characters use the following table: [NUL] [SOH] [STX] [ETX] [EOT] [ENQ] [ACK] [BEL] [BS] [HT] [LF] [VT]...
-
Page 10: Code39 Setup
Code39 Setup Description: To setup Code39 parameters, changes will be effective after scanner ACK response. Scanner Response: ACK / NAK Description Field Values allowed Code 39 Enable CD39EN=1 Disable * CD39EN=0 Code 39 Start/Stop Char Send CD39SS=1 Hide * CD39SS=0 Table 2.5 Code128 Setup Description: To setup Code128 parameters, changes will be effective after scanner... -
Page 11: Power Saving
Table 2.8 Power Saving Time Line: If Power Saving Mode enabled, the Model 200/250/260 goes to minimum power consumption after 15 seconds. In this mode, the green LED is blinking every 2 seconds. The scanner wakes-up by either inserting a barcode or swiping a magnetic card. - Page 12 Magnetic Track Setup Description: To setup each magnetic stripe track parameters, changes will be effective after scanner ACK response. Scanner Response: ACK / NAK Description Field Values allowed Magnetic Track 1, 2, 3 Enable * MAG1EN=1 Disable MAG1EN=0 Enable * MAG2EN=1 Disable MAG2EN=0...
- Page 13 NO-READ Message Setup Description: To setup No-Read parameters, changes will be effective after scanner ACK response. The scanning results of a no read card are the following: Magnetic Stripe (M250/260): If there is a problem in reading a recorded information on a track, the reader reports error using the ASCII string “NR”...
- Page 14 Scanner upgrade Description: To transfer and upgrade scanner software. Changes will be effective after scanner ACK response. Scanner Response: ACK / NAK Example 1: Host: (ASCII value 01 „SOH‟)<A1CODE=Z>(ASCII value 04 „EOT‟) Scanner: ACK Host: switch to Zmodem protocol Scanner: switch to Zmodem protocol (After the file is being transferred) Host: switch back to normal setting Scanner: switch back to normal setting...
- Page 15 Appendix A ASCII ASCII ASCII ASCII [NUL] [space] [SOH] [STX] " [ETX] [EOT] [ENQ] [ACK] & [BEL] [BS] [HT] [LF] [VT] [FF] [CR] [SO] [SI] [DLE] [DC1] [DC2] [DC3] [DC4] [NAK] [SYN] [ETB] [CAN] [EM] [SUB] [ESC] [FS] < [GS] [RS] >...
- Page 16 Appendix B Model 200/250 Serial Port Pin outs (RJ-45) Pin Number Description Reserved VCC (7 - 20 VDC) Reserved Reserved Ground TxD (Transmit Data) RxD (Receive Data) RTS (Request To Send) CTS (Clear To Send) Reserved Table B.1 Model 260 PIN-OUT: RJ45 & Kiosk Connector (10 Pin)