Intelligent dsp based 32 channel analog input card (17 pages)
Summary of Contents for Alphi CPCI-QIPC
Page 1
CPCI™ systems Up to Four IndustryPack Modules ® Dual Ported SRAM between CPCI and DSP C31 REFERENCE MANUAL 739-11-000-4000 Version 1.1 May 1998 ALPHI TECHNOLOGY CORPORATION 6202 S. Maple Avenue #120 Tempe, AZ 85283 USA Tel: (602) 838-2428 Fax: (602) 838-4477...
Page 2
ALPHI TECHNOLOGY reserves the right to make any changes, without notice, to this or any of ALPHI TECHNOLOGY’s products to improve reliability, performance, function or design.
1. GENERAL DESCRIPTION 1.1 INTRODUCTION The CPCI-QIPC is a CPCI expansion card in a 6U form factor. The CPCI-QIPC provides mechanical support and the electrical interfaces for four single width IP modules, or two double width IP modules. Multiple CPCI-QIPC boards may be installed in a single system.
Page 5
SCC8530 Serial Port Dual Port Arbitration IP A IP C Dual Ported SRAM IP B IP D 1M x 32 Figure 1.1: Block Diagram ALPHI TECHNOLOGY CORP. Page 2 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
Page 6
CPCI-QIPC REFERENCE MANUAL Figure 1.2: Jumper Locations ALPHI TECHNOLOGY CORP. Page 3 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
Page 7
CPCI-QIPC REFERENCE MANUAL Figure 1.3: Connector Locations ALPHI TECHNOLOGY CORP. Page 4 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
NOTE: The AMCC has been programmed to request memory above 1 Mbytes. 2.3 CPCI OPERATION REGISTERS The host processor communicates with the CPCI-QIPC module via the AMCC pass-through interface. After the base address registers have been programmed by the CPCI configurator, incoming CPCI I/O or Memory cycles are translated into either accesses to the ALPHI TECHNOLOGY CORP.
For more information about these registers refer to the AMCC PCI controller manual. C31 SIDE 3.1 INTERNAL ORGANIZATION The CPCI-QIPC card is divided into different sections. Each section and its relationship to other sections will be discussed. The CPCI-QIPC sections are: • CPCI interface •...
The Mailbox registers of the AMCCS9533 provide a bi-directional data path that can be used to send data or software control information between the HOST and the CPCI-QIPC module. Interrupts can be enabled based on a specific mailbox event. There are 4 incoming mailboxes and 4 outgoing mailboxes.
D00-D15 IP_D ID Space INTGNT_D $F00740 $F0077F D00-D07 Interrupt vector from IP_D IOSEL_D $F00780 $F007BF D00-D15 IP_D I/O Space Table 3.2: DSP Memory Map ALPHI TECHNOLOGY CORP. Page 9 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
Page 13
16 bits are valid when 32BIT_CD = 0. CBERR_EN Local Bus Error enable Any access to a non-existent IP will never complete since no device will assert *IPACK. ALPHI TECHNOLOGY CORP. Page 10 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
Page 14
The Industry Pack Specification allows for the possibility for an IP to request a DMA transfer. The CPCI-QIPC does not directly support this option. However it is possible for the DSP to recognize a DMA request by polling the C31 STAT2 register. There is no interrupt support or direct DMA support by the DSP.
CPCI-QIPC REFERENCE MANUAL 3.5.8 SERIAL PORT (Read / Write) The DSP processor on the CPCI-QIPC has access to a SCC85C30 serial communication controller. The 8530 provides an RS232C asynchronous serial communication port and an RS422 port. The bootloader and hardware support libraries supplied with the CPCI-QIPC utilizes the RS232C port for a console for standard input and output by the DSP.
AMCC. Hosted operation is default. None If installed, forces PCI reset high for stand alone operation. Hosted operation is default. Table 4.1 Jumper Descriptions ALPHI TECHNOLOGY CORP. Page 13 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
6.1 IP I/O CONNECTORS 50 pin subminiature D shelled connectors are used to route all the IP I/O signals off the card. ALPHI Technology can supply transition modules and cable assemblies to meet any special requirements. Contact the factory for additional information.
Input Receive Data - Input CTS + or RXCLK + Input CTS - or RXCLK - Table 6.4: Serial RS422 / RS485 Port (P3) ALPHI TECHNOLOGY CORP. Page 15 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
By installing jumper blocks on the 20 headers H1 – H20, the IP I/O lines are connected to J4 and J5. Alternatively, the customer can wirewrap a custom pinout if desired. ALPHI TECHNOLOGY CORP. Page 16 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
This is accomplished by inserting a jumper in location W15 for stand alone operation. In a hosted environment, it must be removed. ALPHI TECHNOLOGY CORP. Page 21 Ver 1.1 739-11-000-4000 Part Number : Copyright ALPHI Technology Corporation ,1998...
Need help?
Do you have a question about the CPCI-QIPC and is the answer not in the manual?
Questions and answers