Download Print this page

Advertisement

Quick Links

INTRODUCTION
BEFORE YOU START
The Rebel R-F01 is a professional 1/10 scale rear-wheel drive
competition car and should be built only by persons aged 16 years or
older with previous experience building and operating R/C model cars.
This is not a toy and is not intended for use by beginners or by children
without direct supervision of a responsible, knowledgeable adult. Read
the instruction manual carefully before building.
T.O.P. Racing shall not be liable for any loss, injury or damages, whether
direct, indirect, special, incidental, or consequential, arising from the
use, misuse, or abuse of this product and/or any product or accessory
required to operate this product.
GENERAL PRECAUTIONS
This product is not suitable for children under 16 years of age without
the direct supervision of a knowledgeable adult.
Assemble this kit only in places away from the reach of small children.
First-time builders and users should seek advice from people who
have building experience in order to assemble the model correctly and
to allow the model to reach its performance potential.
Exercise care when using tools and sharp instruments.
Take care when building, as some parts may have sharp edges.
Keep small parts out of reach of small children. Children must not
be allowed to put any parts in their mouth, or pull vinyl bag over their
head.
Immediately after using your model, do not touch equipment on the
model such as the motor and speed controller, because they generate
high temperatures. You may seriously burn yourself by touching them.
Follow the operating instructions for the radio equipment at all times.
Do not put fingers or any objects inside rotating and moving parts, as
this may cause damage or serious injury as your finger, hair, clothes,
etc. may get caught.
Be sure that your operating frequency is clear before turning on
or running your model, and never share the same frequency with
somebody else at the same time. Ensure that others are aware of the
operating frequency you are using and when you are using it.
Always turn on your transmitter before turning on the receiver in the
car. Always turn off the receiver before turning off your transmitter.
Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
Disconnect the battery pack before storing your model.
To prevent any serious personal injury and/or damage to property, be
responsible when operating all remote controlled models.
The model car is not intended for use on public places and roads or
areas where its operation can conflict with or disrupt pedestrian or
vehicular traffic.
Do not use your model:
1.
Near real cars, animals, or people that are unaware that an RC car
is being driven.
2.
In places where children and people gather
3.
In limited indoor spaces
4.
In wet conditions
5.
In the street
6.
In areas where loud noises can disturb others such as hospitals
and residential areas
7.
At night or anytime your line of sight to the model may be
obstructed or impaired in any way.
To prevent any serious personal injury and/or damage to property, please
be responsible when operating all remote controlled models.
ELECTRICAL PRECAUTIONS
Insulate any exposed electrical wiring (using heat shrink tubing or
electrical tape) to prevent dangerous short circuits. Take maximum
care in wiring, connecting and insulating cables. Make sure cables
are always connected securely. Check connectors for if they become
loose. And if so, reconnect them securely. Never use R/C models with
damaged wires. A damaged wire is extremely dangerous, and can
cause short-circuits resulting in fire.
Low battery power will result in loss of control. Loss of control can
occur due to a weak battery in either the transmitter or the receiver
Weak running battery may also result in an out of control car if your
car's receiver power is supplied by the running battery. Stop operation
immediately if the car starts to slow down.
When not using RC model, always disconnect and remove battery.
Do not disassemble battery or cut battery cables. If the running
battery short-circuits, approximately 300W of electrical power can be
discharged, leading to fire or burns. Never disassemble battery or cut
battery cables.
Use a recommended charger for the receiver and transmitter batteries
and follow the instructions correctly. Over-charging, incorrect
charging, or using inferior chargers can cause the batteries to become
dangerously hot. Recharge battery when necessary. Continual
recharging may damage battery and, in the worst case, could build
up heat leading to fire. If battery becomes extremely hot during
recharging, please ask your local hobby shop for check and/or repair
and/or replacement.
Regularly check the charger for potential hazards such as damage to
the cable, plug, casing or other defects. Ensure that any damage is
rectified before using the charger again. Modifying the charger may
cause short-circuit or overcharging leading to a serious accident.
Therefore do not modify the charger.
Always unplug charger when recharging is finished.
Do not recharge battery while battery is still warm. After use, battery
retains heat. Wait until it cools down before charging.
Do not allow any metal part to short circuit the receiver batteries or
other electrical/electronic device on the model.
Immediately stop running if your RC model gets wet as may cause
short circuit.
Please dispose of batteries responsibly. Never put batteries into fire.
EQUIPMENT RECOMMENDED (NOT INCLUDED)
Radio Transmitter
Radio receiver
Batteries for Transmitter
Electronic Speed Control
Steering Servo for 1/10 scale, Low profie
540 Type Motor or Brushless Motor System
Pinion Gear (64P)
3.7V 1S / 7.4V 2S / 7.4V 2S shorty pack
1/10 Scale Body Shell (F1)
Front and Rear Tire Set
Front spoiler and rear wing (Tamiya F1 compatible)
TOOLS RECOMMENDED (NOT INCLUDED)
1.5mm, 2.0mm, 3.0mm Allen Wrench
5.5mm & 7.0mm Hex Socket Wrench
Modelers Craft Knife
Turnbuckle Wrench
Calipers/Ruler
Camber Gauge
Battery Strapping Tape
Shock Oil
Diff. Grease
Paint (for Bodyshell)
NOTE:
The Rebel F1 chassis uses the best available components. All
replacement parts can be purchased from your local hobby or model
shops who carry our products.
This instruction manual contains a blank setup sheet for your own
setup record.
Enjoy building and driving your Rebel F1X!!
Page 1

Advertisement

loading

Summary of Contents for TOP racing Rebel F1X

  • Page 1 Ensure that others are aware of the dangerously hot. Recharge battery when necessary. Continual Enjoy building and driving your Rebel F1X!! operating frequency you are using and when you are using it. recharging may damage battery and, in the worst case, could build •...
  • Page 2 常に送信機のスイ ッチを先に入れ、 その後で車に搭載のレシーバーのス い。 バッテリーの廃棄には責任を持ち、 決して火の中に捨てないよう注意 イ ッチを入れて下さい。 して下さい。 •  スイ ッチを切る場合は、 先にレシーバーのスイ ッチを切り、 その後に送信 機のスイ ッチを切って下さい。 プロポ装置の作動チェックの際は、 ホイル 部を地面から離して下さい。 Enjoy building and driving your Rebel F1X!! •  車を保管する場合は、 バッテリーパックを外して下さい。 •  怪我や、 物への損害を避けるためにも、 操作中は充分に責任を自覚して 下さい。 •  使用する場合、 公共の場所、 公道などの歩行者や、 乗物等と衝突する恐...
  • Page 3 BAG 1 BAG 2 PC-RFCHC035 Front Lower Arm Plate x 2 PC-RSU008 フロントロアーアームプレート King Pin キングピン PC-RFCH026BK MC-MLK002 Front Upper Arm Holder 3 x 20mm Turnbuckle フロントアッパーアームホルダー PC-RFCHC032 PC-RFCHC033 x 1 3 x 20 mm  ターンバックス Front Upper Arm Plate LH Front Upper Arm Plate RH PC-RFCH024RD フロントアッパーアームプレード LH フロントアッパーアームプレート RH...
  • Page 4 BAG 5 BAG 6 TC-PMMS02 x 2 PA-ER0020 Damper Spring Holder TC-PSH002 E-Clip 2.0mm x 1 PC-RDT001BK Rear Axle / リアアクスル ダンパースプリングホルダー Shock Bladder Eクリッ フ 2.0mm ショックブラダー x 1 TC-PMRS01 Shock Piston TC-PSH101RD ショックピストン TC-PSH101RD Shock Spring Adjuster 1.2mm - 2 hole Shock Bottom Cap ショックスプリングアジャ...
  • Page 5 BEARING SCREW NUTS x 5 PA-SS0303BK x 34 PA-CM0306BK x 25 PA-BM0306BK PA-SB168F Set Screw Countersunk Screw Button Head Screw PA-SNF4BK x 5 PA-CM2506BK Flanged Steel Ball Bearing イモネジ 皿ビス ボタンヘッドネジ M4 Steel Serrated Wheel Nut Black Countersunk Screw フランジ付スチールボールベアリング M3 x 3mm M3 x 6mm M3 x 6mm...
  • Page 6 アッパーフロントサスペンション / UPPER FRONT SUSPENSION FINISHED BAG 1 Button Head Screw 完成 1 Pair ボタンヘッドネジ 左 右 PA-BM0306BK 1ペア M3 x 6mm LEFT RIGHT Button Head Screw M3 x 6mm ボタンヘッドネジ M3 x 6mm PO-PCH011RD Special Chassis Nuts (Red) スペシャルシャーシナット Special Chassis Nuts (Red) スペシャルシャーシナッ...
  • Page 7 サスマウント (続き) / SUSPENSION MOUNT (cont’d) BAG 2 PA-ER0020 2.0mm E-Clip Button Head Screw 2.0mm Eクリッ フ ボタンヘッドネジ ボタ ッドネ M3 x 10mm M3 x 10mm SCREW Button Head Screw Button Head Screw make 2 AW-KS050RD PA-BM0310BK ボタンヘッ ドネジ ボタンヘッ ドネジ 2個作成...
  • Page 8 リアアクスル 組立て / REAR AXLE ASSEMBLY SCREW PA-BM2508BK Button Head Screw M2.5 x 8mm ボタンヘッドネジ M2.5 x 8mm PA-BM0310BK FINISHED Button Head Screw M3 X 10mm 完成 ボタンヘッドネジ M3 X 10mm PA-CM0306BK Countersunk Screw M3 x 6mm 皿ビス M3 x 6mm BAG 3 AW-M300RD Ultra Wide Collar 3 x 7 x 3.0mm ウルトラワイドカラー 3 x 7 x 3.0mm Collar...
  • Page 9 リアシャーシ組立て / REAR CHASSIS ASSEMBLY BAG 4 Chess Head Screw AW-S100RD チェスヘッドネシ M2 x 7mm Collar 3 x 5.5 x 2.0mm Collar 3 x 5.5 x 1.0mm Countersunk Screw Counters カラー 3 x 5.5 x 2.0mm カラー 3 x 5.5 x 1.0mm 皿ビス...
  • Page 10 リア デフ / REAR DIFFERENTIAL リア デフ / REA BAG 5 AW-AS200RD Axle Spacer アクスルスペーサー PA-HM2506BK Hex Head Screw 六角ビス Ceramic Diff. Ball 1/8” M2.5 x 6mm セラミックデフボール 1/8” BEARING PA-SB0168 Axle Spacer 2mm アクスルスペーサー 2mm Ball Bearing 1/4 x 3/8 Ball Bearing 1/4 x 3/8 ボールベアリンク 1/4 x 3/8 ボールベアリンク 1/4 x 3/8 PA-SB168F Flanged Ball Bearing 1/4 x 3/8...
  • Page 11 SHOCK ASSEMBLY / ショック組立て Note: You could choose from a variety of shock piston to suit your needs. 2mm E-Clip 注意 :  さまざまなショックピストンから必要に応じて選ぶ 2mm E- クリッ プ 2mm E- クリッ プ FINISHED 完成 1.0mm hole 1.2mm hole 10.2mm PA-ER0020 2mm E-Clip 2mm E - クリッ プ PA-CM0306BK Countersunk Screw M3 x 6mm 皿ビス M3 x 6mm...
  • Page 12 サーボマウント組立て / SERVO MOUNT ASSEMBLY SCREW PA-SP0307 Button Head Screw FINISHED Flat Washer M3 x 7 x 0.5 ボタンヘッドネジ 完成 M3 x 6mm フラッ トワッシャー M3 x 7 x 0.5 x 17 PA-BM0306BK Button Head Screw M3 x 6mm ボタンヘッドネジ M3 x 6mm PA-CM0306BK Countersunk Screw M3 x 6mm...
  • Page 13 フロントスポイラー&リアウィング / FRONT SPOILER &REAR WING BAG 14 PA-FN00M3 M3 Nut M3 ナット PA-LN00M4 M4 Steel Lock Nuts M4 スチールロックナット Button Head Screw ボタンヘッドネジ M3 x 10mm *NOTE: Sold Separately PA-CM0420BK *注意 :  別売 Countersunk Screw M4 x 20mm 皿ビス M4 x 20mm M4 Steel Lock Nuts M4 スチールロックナット...
  • Page 14 タイヤ取付け / TIRE INSTALLATION BAG 15 PA-SNF4BK M4 Steel Serrated Wheel Nut Black M4 スチールセレート付ホイルナット黒 AW-M5100RD Collar 5 x 7 x 1.0mm カラー 5 x 7 x 1.0mm AW-M5050RD Collar 5 x 7 x 0.5mm カラー 5 x 7 x 0.5mm PA-SB1005 Ball Bearing 5 x 10 x 4mm ボールベアリンク 55 x 10 x 4mm PA-LN00M3 M3 Lock Nut...
  • Page 15 Your Rebel F1X is now クロスバッテリーポジション ready to RUN!!! Cross Battery Position Rebel F1X 走行用意!!! て ストレートバッテリーポジション Straight Battery Position Page 15...
  • Page 16 セッティング記録 / SETUP RECORD 名前: 日付: トラック: Name: Date: Track: 国籍: 条件: 温度: Country: Condition: Temperature: FRONT WHEEL BASE : BATTERY POSITION : WIDE NORMAL CROSS STRAIGHT Screw No Screw サーボ ポジション調整 SEVRO Position Adjustment フロントエンド / FRONT END: ステアリングブロック STEERING BLOCK センター ショック / CENTER SHOCK 1.0mm 2hole...
  • Page 17 セッティング記録 / SETUP RECORD 名前: 日付: トラック: Name: Date: Track: 国籍: 条件: 温度: Country: Condition: Temperature: FRONT WHEEL BASE : BATTERY POSITION : WIDE NORMAL CROSS STRAIGHT Screw No Screw サーボ ポジション調整 SEVRO Position Adjustment フロントエンド / FRONT END: ステアリングブロック STEERING BLOCK 10.2 センター ショック / CENTER SHOCK 1.0mm...
  • Page 18 Rebel - Ball Cup - 16mm (5pcs) SG-K64084 Spur Gear 64P 84T SG-K64100 Spur Gear 64P 100T TI-RF1XS1 Rebel F1X Titanium M3 Screws Set (76pcs) SG-K64096 Spur Gear 64P 96T - Kit Std SS-KM01BK Servo Savers Mid size w/holes Stainless Steel Hex Socket Set Screw...