NAX 500C Manual
  1. Manuals
  2. Brands
  3. NAX Manuals
  4. Chainsaw
  5. 500C
  6. Manual

NAX 500C Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NAX 500C
1

Advertisement

Table of Contents
loading

Related Manuals for NAX 500C

Summary of Contents for NAX 500C

  • Page 1 NAX 500C...
  • Page 3 CHAIN SAW NAX 500C...

  • Page 4: Chain Saw Construction And Overview Drawings

    CONSTRUCTION OF CHAIN SAW AND PREVIEW DRAWINGS Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5...
  • Page 5 Fig. 6 Fig. 7 Fig. 9 Fig. 10 Fig. 8 Fig. 11...
  • Page 6 Fig. 12 Fig. 13 Fig. 14 Fig. 15...
  • Page 7 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20 Fig. 21...
  • Page 8 Fig. 22 Fig. 23 Fig. 24 Fig. 25 Fig. 26 Fig. 27...
  • Page 9 Fig. 28 a Fig. 29...
  • Page 10 Fig. 30...

  • Page 11: Table Of Contents

    Original operation manual, edition 1/2020 Translation of the original operation manual from polish language This manual should be treated as an integral part of the device. It should be stored in the place provided for it so that it is easily accessible.

  • Page 12: Technical Data

    TECHNICAL DATA CIRCULAR COMBUSTION SAW Type, model NAX 500C Engine TT-1E48F series BS Fuel mix 40: 1 (4 l of gasoline for every 100 ml of two-stroke oil) Fuel tank capacity 550 cm Mix oil (recommended) Briggs & Stratton for two-stroke engines...

  • Page 13: Description Of Graphic Pages And Pictograms

    DESCRIPTION OF GRAPHIC PAGES AND PICTOGRAMS Pictograms page 2.A Attention! Danger. Exercise special caution. Important! Read the instructions and follow the warnings. Risk of fire or explosion. Gasoline is highly flammable. Keep out of the reach of children. It is prohibited to work in the rain. Note: Exhaust gases are harmful to health.
  • Page 14 SAFETY DURING WORKING WITH FUEL  The internal combustion engine is designed to run on gasoline or a fuel mixture (see type of fuel in the device's technical data).  Gasoline should be stored only in specially prepared containers (canisters). ...

  • Page 15: Detailed Safety Regulations

     Repair should be performed by a qualified person using only original spare parts. This will ensure further safe operation of the device. It is recommended to have any service performed by an authorized NAX service center. CAUTION! Danger of suffocation when children play with the packaging. The packaging, especially the foil bag, should be stored out of the reach of children.
  • Page 16  Safety devices (e.g. cutting unit cover, housing, handle, engine switch) are in good technical condition and work properly;  Before adjustment, cleaning, maintenance, switch off the engine.  Do not use the device when other people, especially children or pets, are nearby. ...
  • Page 17  When cutting through, always use the buttress as a fulcrum. Holding the chainsaw by the main handle, guide it with the auxiliary handle.  If it is not possible to cut the material at once, pull the saw back slightly, move the buttress and continue cutting by slightly raising the main handle of the saw.

  • Page 18: Safety And Producer's Liability

    ADDITIONAL INFORMATION FOR THE USER Performing maintenance and adjustment work before or after the season can be a problem even for advanced users. The NAX company would like to offer you a service consisting in preparing the machine for storage and / or work. The scope of this service may include: candle replacement, cleaning, maintenance, oil change, filter replacement and lubrication of moving parts, knife sharpening and balancing, as well as other work related to the adjustment and maintenance of equipment.

  • Page 19: Construction Of A Chainsaw

     Use extreme caution when cutting small branches and trees, as thin material can get stuck in the saw chain and hit the operator or throw him off balance.  When cutting stressed boughs, be careful not to be hit when the stress in the wood fibers is reduced. ...
  • Page 20  screw the fuel filler cap 11 (Fig. 1). For chain lubrication, it is best to use a guide and chain preparation or a special NAX chain lubricant. CAUTION! Do not use used or regenerated oil, as this may damage the oil pump.

  • Page 21: Starting The Saw

    Check chain lubrication system. After starting the engine, use the gas control lever to set the maximum speed and check that the chain is spraying oil as shown on Fig. 9. The oil flow for chain lubrication can be adjusted by inserting a screwdriver into the bottom slot on the clutch side (Fig. 10). The flow should be adjusted according to the operating conditions.

  • Page 22: Operation

    It is extremely important that the brake is checked for proper operation before each use and that the chain is sharp in order to maintain the correct level of protection against the chainsaw bouncing back. Removing protective devices, improper maintenance, or replacing the guide bar or chain with the wrong equivalent can increase the risk or cause serious injury.
  • Page 23 CAUTION! If, after adjustment, the chain moves while the engine is idling, have it repaired at the NAX Authorized Service. Mixture composition adjustment: this operation should be carried out by the service, as incorrect adjustment may cause the engine to overheat or seize.

  • Page 24: Transport

    Sharpening the chain yourself requires the use of special tools and skills, so it is recommended to entrust the sharpening of the chain to qualified persons or gardening tools services. An authorized NAX service is recommended.

  • Page 25: Storage

    STORAGE Keep the chain saw in a dry, ventilated and safe place out of reach of children. If the chain saw is not in use, it should be stored clean, on a flat and dry surface. If the break in operation is longer than 3 months it is necessary to: ...

  • Page 26: Review And Diagnosis Of Problems

    REVIEW AND DIAGNOSIS OF PROBLEMS INSPECTIONS Prior to After work After each Once In case of Inspections Monthly each use or daily refueling a week damage required visually check (condition, leaks) Entire Machine clean Throttle switch and lock, combination test switch test Chain brake...

  • Page 27: Device Assembly Diagrams

    The product purchased by you is intended for amateur (hobby) use only. If the equipment is used for other purposes (commercial, professional), it will lose the guarantor's liability for the purchased equipment. You can find information on the warranty and the NAX service network in the attached warranty card.

  • Page 28: Declaration Of Conformity

    DECLARATION OF CONFORMITY        ...
  • Page 29 WARRANTY Dear Sir or Madam, Thank you for purchasing our product and congratulations on your right choice. The device that you bought was designed and manufactured according to the latest technologies and represents global standards of quality and reliability, while being environmentally friendly. We remind you to carefully read the commissioning and operation procedures before using the device;...

  • Page 30: Warranty Conditions

    16. NAX is not responsible for direct or indirect damages, losses or costs resulting from the use or inability to use the device for any purpose. 17. If it is necessary to carry out activities related to the maintenance of the device before starting the repair, the Service / Store may carry out such activities against payment with the consent of the user / advertiser.

  • Page 31: Warranty Card

    I declare that I am official NAX Authorized Distributor. Submission of a statement inconsistent with the facts by an entity that is not an authorized NAX Distributor may result in criminal liability of the seller pursuant to art. 271 and Article 267 of the Penal Code.

Table of Contents