Advertisement
Quick Links
System 2000
System 2000 automatic control switch 360°
System 2000 automatic control switch 360° pure white
Order-No. : 2270 02
System 2000 automatic control switch 360° colour aluminium
Order-No. : 2270 04
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. At the same time, take into account all circuit breakers that supply dangerous
voltage to the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The load is not electrically isolated from the mains even when the device is switched off.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
(1) Flush-mounted insert
(2) Motion detector cover
(3) Adjuster sens
(4) Adjuster time
(5) Adjuster lux
(6) Brightness sensor
(7) LED display, behind the lens
(8) Lens
(9) Decor ring
(10) Push-on cover
82563812
Figure 1
18.11.2011
1/8
Advertisement
Related Manuals for Gira System 2000
Summary of Contents for Gira System 2000
- Page 1 System 2000 System 2000 automatic control switch 360° System 2000 automatic control switch 360° pure white Order-No. : 2270 02 System 2000 automatic control switch 360° colour aluminium Order-No. : 2270 04 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons.
-
Page 2: Operation
System 2000 System 2000 automatic control switch 360° 3 Function Intended use Automatic switching of lighting depending on the heat motion and ambient brightness. Operation with concealed insert for dimming, switching or extension insert, 3-wire Ceiling installation on flush-mounted insert... - Page 3 System 2000 System 2000 automatic control switch 360° Dimming light with dimming insert The light can be dimmed using a 2-wire extension. The light remains at the dimmed value until the run-on time has elapsed. Press 2-wire insert at top or bottom until the desired brightness is reached.
- Page 4 System 2000 System 2000 automatic control switch 360° Figure 3: Detection area dependent on the direction of movement i Note direction of motion (Figure 3). Motions that are transverse to the motion detector (Drawing B) can be detected better than motions towards or away from the motion detector (Drawing A).
- Page 5 System 2000 System 2000 automatic control switch 360° 5.2 Commissioning Testing the detection area Figure 4: Test setting The motion detector is fitted and connected. Pull off push-on cover (10) Pull off decor ring (9). Set sens adjuster (3) to max(Figure 4).
- Page 6 System 2000 System 2000 automatic control switch 360° Limiting the detection area Figure 5: Push-on cover The push-on cover can be used to limit the detection area, e.g. in order to mask out interference sources. Cover size Detection area on the floor Complete push-on cover Ø...
-
Page 7: Troubleshooting
System 2000 System 2000 automatic control switch 360° Attach decor ring. i To make the short-time operation independent of brightness, turn lux adjuster (5) to 3. Setting the brightness threshold Only when the brightness drops below the threshold will the light be switched on when there is motion in the detection area. -
Page 8: Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade. Please submit or send faulty devices postage paid together with an error description to your responsible salesperson (specialist trade/installation company/electrical specialist trade). They will forward the devices to the Gira Service Center. Gira Giersiepen GmbH & Co. KG...