Panasonic PT-56TWD63 Operating Manual page 29

Convergence (cont.)
Note: Convergence seldom needs adjusting except after
moving the PTV or to make minor adjustments.
Procedure
• Press OK to enter convergence sub-menu field.
• Press CH or CH
• CONVERGENCE ADJ. - Select to correct minor
convergence problem.
Note: After selecting, press OK to continue
CONVERGENCE ADJ.
• RESET TO DEFAULT - Select to set convergence
to factory default setting.
Note: After selecting, press OK to activate RESET
TO DEFAULT feature.
Convergence
Convergence Adj.
Reset to Default
CONVERGENCE ADJ.
Procedure
• After pressing OK the align Green to Center screen will
be displayed.
• Then use the navigation buttons on the remote control
to align the horizontal and vertical green lines on screen,
with the cabinet reference marks on top center and left
center of cabinet, as shown below.
Reference Marks
Front of cabinet
• Press OK button to display red center correction screen.
• Use the navigation buttons on the remote control to align
the red cross with the white cross pattern at the center of
the screen.
Note: To prevent picture tube damage do not leave
test pattern on for an extended period of time.
• Then press "0" on the remote control keypad to display
the BLUE center correction screen, repeat procedure for
adjusting blue. If needed press "0" again to return to
RED correction screen.
Note: An adjusted cross pattern appears white with a minimum
of color protrusion.
If Red Is Protruding From
Center Cross, Press CH And
VOL Key To Correct
Up
Left Right
Down
PRESS 0 To Adjust Blue
Press Ok To Continue
to select:
SELECT
OK
MENU EXIT
to return
Press CH And VOL Key To
Align Green Lines To The
Center Mark On The Cabinet
Up
Right
Left
Down
Press Ok To Continue
If Blue Is Protruding From
Center Cross, Press CH And
VOL Key To Correct
Press
Up
"0"
Left
Down
PRESS 0 To Adjust Red
Press Ok To Continue
NINE POINT CONVERGENCE CORRECTION
Note: Remote Control must be in TV mode.
Procedure
• Press OK button to display red correction screen.
• Press the 1 through 9 keypad buttons on the remote
control to select the desired convergence position.
• Use the navigation buttons to align the RED cross with
the white cross pattern.
Note: An adjusted cross pattern appears white with a minimum
of color protrusion.
• Press "0" on the remote control keypad to display the
BLUE correction screen, then repeat procedure.
2
1
Press # Key To Select Pos.
Press CH And VOL Key To Corr.
4
Correcting Red
Press 0 To Adjust Blue
PRESS ACTION TO EXIT
Press Ok To Exit
8
7
• To exit convergence screen press OK button, then press
EXIT to quit all menus.
Cable Module Info
This menu is used to provide information when a DCM
(Digital Cable Module) is inserted into the DCM
INTERFACE (POD INTERFACE) slot on the back of the
projection television. If no DCM is present and you try to
access the Cable Module Info, the message 'Cable Module
Not present' will be displayed on screen. To receive the
features offered by your cable company, you may have to
subscribe to those services.
Note: Please contact your cable company regarding availability
of the DCM (Digital Cable Module). The cable module is
needed to
available) through the cable input. You may also able to
order call-ahead pay per view events.
Right
M O
ENU PERATIONS
2 3
1
Press # Key To Select Pos.
Press CH And VOL Key To Corr.
4 6
Correcting Red
Press 0 To Adjust Blue
PRESS ACTION TO EXIT
Press Ok To Exit
9
8
7
3
1
Press # Key To Select Pos.
Press CH And VOL Key To Corr.
Press
6 4
"0"
Correcting Blue
Press 0 To Adjust Red
PRESS ACTION TO EXIT
Press Ok To Exit
9
7
receive premium digital services (where
2 3
6
9
8
27