Chapter Safety Principles of CO Laser Safety Ratings The Safety Interlock System Safety Labels Safety Measures Operating Environment LaserPro StellarMark CIIA-Li User Manual | 4...
In compliance with CDRH standards, the required warning labels are affixed at the time of manufacture to the LaserPro StellarMark CIIA-Li in the appropriate locations. These labels are not to be modified in any way or removed for any reason. Please familiarize yourself with the specific labels and their locations on the machine.
Page 6
This label is located at the right-back side of machine. All the product information such as Serial Number, Model Numbers, Laser Power and Electric power can be found here. Before requiring any tech support, always provide service person the information on this label. LaserPro StellarMark CIIA-Li User Manual | 6...
Page 7
CE Label This label indicates the class level of CE Emergency Stop Label This label indicates the emergency stop button. You can find this label on the left side of the power supply unit LaserPro StellarMark CIIA-Li User Manual | 7...
Always wear safety goggles when the laser system is in operation. Reflective materials such as mirrors, enameled brass and anodized aluminum may LaserPro StellarMark CIIA-Li User Manual | 8...
StellarMark CIIA-Li. Improper work environments may lead to operational malfunction and/or unsafe working conditions. The LaserPro StellarMark CIIA-Li should be placed and operated in a clean environment, avoid places where the machine is exposed to high temperatures, dust, or high humidity...
Page 10
Choose a location that is large enough to accommodate the machine, the computer and a work/storage table. Have a fire extinguisher close to the working location at all times. Make sure your smoke/fire detecting system is functioning. LaserPro StellarMark CIIA-Li User Manual | 10...
3.1 Laser Marker 3.1.1 LED Panel There are 3 LED lights on the panel and they will indicate out three working status of “Over Temp”, “Laser On” and “Power on” of the laser marker. LaserPro StellarMark CIIA-Li User Manual | 14...
Page 15
Working Area Focal Length (FL) 10 x 10 25.89 ± 1 50 x 50 65.268 ± 1 70 x 70 91.16 ± 1 140 x 140 196.43 ± 2 LaserPro StellarMark CIIA-Li User Manual | 15...
The scan lens is very fragile and careful while the cleaning and installing. Defective or unworkable due to abuse, mishandling, misuse, accident, alteration, negligence, improper installation, deficient cleaning or other causes will not be covered in the warranty. 3.2 Machine Dimension LaserPro StellarMark CIIA-Li User Manual | 16...
Page 17
LaserPro StellarMark CIIA-Li User Manual | 17...
For instance the 70x70 mm scan lens can only tolerate a distance which is +- 1mm different from the recommended working distance of 105mm. If the working distance is set and out of the recommended range, the output work produced will be unsatisfactory. LaserPro StellarMark CIIA-Li User Manual | 19...
With this tool, you can always have the best working distance for different materials by just place your desired marking material on the z axis table and move the z axis table up until the mark material touches the bottom screw of Pyramid Ruler. LaserPro StellarMark CIIA-Li User Manual | 20...
The StellarMark C-12IIA-Li as been designed to work with AC Auto Switch 100 & 240 VAC, 50-60Hz 5.2 Power Cable Connection Step 1. Connect the laser marker power cable to the laser marker. LaserPro StellarMark CIIA-Li User Manual | 22...
Page 23
Step 2. Connect the D_SUB cable 25pin &15pin between the PCI card and the laser marker. Step 3. Turn on the master power for laser Marker LaserPro StellarMark CIIA-Li User Manual | 23...
Page 24
Every time you turn off the power, you are required to re-start G-Mark Advance marking software, because the connection between computer and control unit is disconnected when the power is off, so the marking software is unable to control the laser firing. LaserPro StellarMark CIIA-Li User Manual | 24...
Page 27
Pin Layout & Connection J18 (Start) Functions of Start (i.e. J18 Pin-2) 1-2 Short Positive level trigger for Start. 2-3 Short Negative level trigger for Start. LaserPro StellarMark CIIA-Li User Manual | 27...
Page 28
2) PGM Ready logic high (1) as G-Mark not initiated. 1) PGM Ready logic high (1) as G-Mark initiated. 2-3 Short 1-2 Short 1-2 Open 2) PGM Ready logic low (0) as G-Mark not initiated. LaserPro StellarMark CIIA-Li User Manual | 28...
Page 29
1-2 Short 1-2 Open 3) Mark Ready logic low (0) as laser marking activated. 4) Mark Ready logic high (1) as laser marking completed. 5) Mark Ready logic low (0) as G-Mark quitted. LaserPro StellarMark CIIA-Li User Manual | 29...
Simple Cattle Horn Female 2*13P to Simple Cattle Horn Female 2*10P to Simple Cattle Horn Female 2*13P Simple Cattle Horn Female 2*10P Cable 15cm Cable 2) Remove the PMC2 card from the computer (if it is already installed) LaserPro StellarMark CIIA-Li User Manual | 30...
Page 31
3) Connect the two 26 Pin Cables to the JF2 and JF4 slots of the PMC2 board 4) Connect the two 20 Pin Cables to the JF6 and JF8 slots of the PMC2 board LaserPro StellarMark CIIA-Li User Manual | 31...
Page 32
5) Connect the other side of the 26 Pin cables to the JF2 and JF4 slots on the PMC2 Signal Trace Board Assembly 6) Connect the other end of the 20 pin cables to the JF6 and JF8 slots of the PMC2 Signal Trace Board Assembly LaserPro StellarMark CIIA-Li User Manual | 32...
Page 33
8) Insert the PMC2 into a PCI slot on the computer and assemble the PMC2 Signal Trace Board Assembly to the computer 9) Connect a D-Sub 25 pin cable to the connector on the PMC2 Signal Trace Board Assembly LaserPro StellarMark CIIA-Li User Manual | 33...
Page 34
10) Connect the D-Sub 25 pin cable to the I/O interface 11) Installation completed LaserPro StellarMark CIIA-Li User Manual | 34...
Chapter Software Setup Recommended Computer Configuration Software Installation for Windows System Software Installation for MAC System LaserPro StellarMark CIIA-Li User Manual | 35...
Take out the G-Mark installation CD from the accessories kit Step 2 Insert the G-Mark installation CD into the CD-ROM drive Wait a few seconds for the CD Manager to begin the Setup automatically LaserPro StellarMark CIIA-Li User Manual | 36...
Page 37
Step 3. Click on 32 bit or 64 bit version from the menu of the G-Mark installation CD depending on your operating system Step 4. Set the destination directory and click "Next>" LaserPro StellarMark CIIA-Li User Manual | 37...
Page 38
Step 5. Select "Next>" Step 6. Installing Step 7. At 95% completion of the installation, the ModelManger window will show LaserPro StellarMark CIIA-Li User Manual | 38...
Page 39
Step 8. Select your series & model type LaserPro StellarMark CIIA-Li User Manual | 39...
Page 40
Step 9. Click “OK” Step 10. Click “Finish” to complete the installation LaserPro StellarMark CIIA-Li User Manual | 40...
Page 41
If “Laser marking controller” is not showing at the lower right hand corner of your computer screen, G-Mark will not be able to be activated. Please perform the following steps: A. Please go to “Control” and click on “System” LaserPro StellarMark CIIA-Li User Manual | 41...
Page 42
B. Then click on “Hardware” and go to the “Device manager” C. Please check if there is any “!” USB device from the below chart: LaserPro StellarMark CIIA-Li User Manual | 42...
Page 43
D. Then click on “USB Driver’ and click on right mouse button and update the driver. Click on ”Browse my computer for driver software” LaserPro StellarMark CIIA-Li User Manual | 43...
Page 44
Key in the specific path: “C:\Program Files\G-Mark Lib \Drivers\MC1. Then press “Next.. G. Press “Finish” and now you can activate the G-Mark software LaserPro StellarMark CIIA-Li User Manual | 44...
Windows OS in MAC computers and run Windows based software under MAC computer and output with G-Mark. Step 1. Purchase Parallels Desktops on its official website. Step 2. Install Parallels Desktops under Mac OS environment. LaserPro StellarMark CIIA-Li User Manual | 45...
Page 46
Step 3. Read Software License Agreement and press “Accept” to continue installation Step 4. Enter your Mac OS X User Name and Password then press “OK” LaserPro StellarMark CIIA-Li User Manual | 46...
Page 47
Step 5. Press “Active” Step 6. Press “OK” when activation is complete. LaserPro StellarMark CIIA-Li User Manual | 47...
Page 49
Step 8. Press “Register” and “OK” to complete the installation of Parallels Desktop. Step 9. Open Parallels Desktop (in the Applications folder) then choose File LaserPro StellarMark CIIA-Li User Manual | 49...
Page 50
Step 10. Press “Install Windows from DVD or image file” then press “continue” to install windows OS Step 11. Select CD-ROM drive with the Windows installation CD LaserPro StellarMark CIIA-Li User Manual | 50...
Page 51
Step 12. Enter the Windows OS product key Step 13. Select how you would like to run your Windows program. LaserPro StellarMark CIIA-Li User Manual | 51...
Page 52
Step 14. After the prior setting is complete the windows OS installation procedure will start automatically. Step 15. Windows OS installation is complete then you can refer to “6.2 Software Installation for windows system” to install G-Mark / G-Mark Library. LaserPro StellarMark CIIA-Li User Manual | 52...
7.1 Import Lens Parameter Please perform the following steps: Step 1. Start the G-Mark program. Step 2. Select File Configuration Import/Export. Step 3. Check the Application Config, Lens Setting, Object Default and Machine Check Config selections. LaserPro StellarMark CIIA-Li User Manual | 54...
Page 55
If there is no “Lens Parameter” folder found under G-Mark installation CD, please skip to follow ”7.2 Lens Parameter Card” instructions. LaserPro StellarMark CIIA-Li User Manual | 55...
Page 56
Step 6. Click the "Import" button. Step 7. Click on the "OK" button after the Status screen shows Complete. Step 8. Click on "OK" when the "Restart message prompts up. LaserPro StellarMark CIIA-Li User Manual | 56...
Page 57
Step 10. The Lens parameter can be found in the Lens list. (Named with the serial number of your machine.). Step 11. Click on "Apply" after selecting the Lens and the settings will be loaded. LaserPro StellarMark CIIA-Li User Manual | 57...
Or the marking lines will be distorted or will have an improper scale of the marking content. Step 1. Take out the lens parameter card from the accessory kit Step 2. Open G-Mark marking software Step 3. Click on work area from property table and press “Lens Manager…” LaserPro StellarMark CIIA-Li User Manual | 58...
Page 59
Step 4. Press “New” to create a new name for the lens and press “OK” Step 5. Click “Correction…” to settings lens LaserPro StellarMark CIIA-Li User Manual | 59...
Page 60
Step 6. Fill in the numbers that are showing on the card to the below table. Press “Exit” to save the settings of the lens NOTE If the size of scan lens is changed, the lens parameter will be varied, too. LaserPro StellarMark CIIA-Li User Manual | 60...
Step 1. Create new name for the new lens. Step 2. Change the mark area and press “Exit” to save the settings Step 3. Mark the below pattern and check the output quality. LaserPro StellarMark CIIA-Li User Manual | 61...
Page 62
Increased like 0.002; while if now it become indentation, the X value will have to be reduced to as 0.0014. Keep adjusting the value until it is acceptable. Step 6. If the square is trapezoid, go back to the “lens setup” to correct the irregular square. LaserPro StellarMark CIIA-Li User Manual | 62...
Page 63
Keep adjusting the value until it is acceptable. Step 8. If there is an irregular parallelogram, go to the “lens parameter” under the Configure to correct the irregular angle. Step 9. Keep adjusting the value until it is acceptable. LaserPro StellarMark CIIA-Li User Manual | 63...
Page 64
Step 10. Measure the lengths of A, B, C, D and E of the square pattern. Make sure these lengths match to the expected length you set from the marking software. Step 11. If not, correct scale proportionally. LaserPro StellarMark CIIA-Li User Manual | 64...
Chapter Basic Maintenance Cleaning the Lenses LaserPro StellarMark CIIA-Li User Manual | 65...
Page 66
NOTE Acetone is an EXTREMELY FLAMMABLE LIQUID AND VAPOUR. The vapour is heavier than air and may spread long distances making distant ignition and flashback possible. LaserPro StellarMark CIIA-Li User Manual | 66...
Page 67
Use finger cots or rubber gloves when cleaning. If a problem ever arises with the G-Mark Advance software or the StellarMark marking machine, be sure to notify your distributor as soon as possible. LaserPro StellarMark CIIA-Li User Manual | 67...
Page 69
Microsoft Windows 2000 / XP / Vista (32 Bit) / Win 7 (32 Bit) ( Desktop or Laptop PC ) Safety Class 4 ( Cass 3R available with safety door ) All spec are subject to change without any prior notice. ** Material dependent. www.delinit.by LaserPro StellarMark CIIA-Li User Manual | 69...