Advertisement
Quick Links
I
!il.
I
I
I
ll
I
t
I
tTEI\,'t54417
Ti==liöäffiH
Thank
you
for
purchasing
this
TGU-o'| unit.
The
TcLl-o1 is
a
lightweight, compact gyro which was
designed
controlan
B/C car's steering.
lt
isveryeasy
to
set up and
if
a
transmitterwith
3
or more channels
is
used,
the gyro's sensitivity can be adjusted from
thetransmitter.
aRead
carefully
and fully
understand
the
instruc-
tions
prior
to
use. Mako sure
to
read
the
cautions
below to ensure
safe
operation.
aPlease
keep these instructions for reference.
Active Steering Assist Unit
{TGU-01)
Specifications
Ocyro
Type:
MEMS
Vibration Structure
Ooperating
Voltage
:
DC
4.0V-8.4V
aourrent:
30mA (without servo)
aOperating
Temperature
:
-10'C-45'C
ODimensions
:
20.5x20.5x11.0mm
(excluding
prokusions)
aweight:3.59
aFunctions
:
Ocyro
Sensitivity Trim
OLED
lndicator
(3)Servo
Selection Switch {Digital/Analog)
*This
unit
may
not operate properly
with
R/C systems
otherthan
those from
Tamiya
and Futaba.
(Nomenclature
/
Functions»
aPon2
{Gyro Sensitivity lnput)
I
aPort3
1
lsteering
Servo Output)
aServo
Selection
Switch
(Digital/Analos)
\
aPort
1
aGyro
Direction
Switch
aTrim
Knob
-----
(Limit/Sensitivity)
LED
lndicator
Cöunterc öckwise
lR.dl
((How
to
Connect))
lncluded Connector
(Black)
Steering Channel
arrrltt
r
To Port
2
To
Port
1
Receiver
I
a
a
I
a
t
a
I
XGyroChannel(3CH)
I r I I I It
Xll
not
using transmitter
to
adjust
gyro
sensitivity,
do
not
connect the
included Connector(Red).
((lnstallation»
The
TGU-01 unit
is
extremely seflsitive to vibrations.
Use
double-sided
spongetapeto
secure
it perpend
icularly
to
the movement axis
at
a
location where
it is less
suscepti-
ble
to
vibrations. Bundle and position cables
to
avoid
contact
with
moving
pans
while avoiding
excessive
*Make
sure
lo
install
parallelto
chassis.
TGU-o'! lnstallation
A
GAUTIoNS
aMake
sure that th€
transmitte/receiver
batte
es have
sufficient voltage
for
operation. Check battery
voltage
during TGU-01
setup in order
to
det€rmine
appropriate
driving time.
aAfter
switching on
the
TGU-o1/receiver power source,
do not
hendle
the chassis
or operate
the
st€oring
for
3
seconds. TGU-0'I
will
undergo
Start-Up, and if
in
AVCS
Mode, undergo neutral position calibration. Servo will
move l€ft and dght to signal completion
of
Start-up.
aAlways
check
the
movement
direction of
lhe
TGU-01
unit's gyro.
lf
the direction
is
reversed,
the
car
may
experience rollovers and
lead
to dangerous situations.
aDo
not
hit or
drop
the
TGU-01
unit
against
hard
objects/surfaces.
Since
the
TGU-01
is
extremely
sensitive
to
vibrations,
§uchshocks maydamagethe
unit,
aoo
not
use
trim or
mixing while in
AVCS Mode. The
TGU-01 handles all adjustments when
in
AVCS
Mode, so
using
the trim
or
mixing will upset the neutral
position
calib.ation.
ause
tor
B/C car models
only. This
product
has been
designed
specificallylor
R/C
cars
and cannot
be used
for
other
applications.
aDo
not
use an
analog servo while in Djgital Servo
(DG)
Mode
as this
may damage
the
servo. Analog
seruos
should
be
used
inAnalog
Sorvo{AN) Mode.
Advertisement
