Installation - Renkforce 1381002 Operating Instructions Manual

Operating instructions
CCTV Camera dummy
Item no. 1381002
Intended use
This product is a dummy that resembles a functional surveillance camera and is
intended for use as deterrent in secluded and critical areas (e.g. driveways, entrance
areas, etc.). The product is suitable for outdoor installation. Power is supplied via
2 AA batteries (not included).
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Camera dummy
• 3x screws
• 3x dowels
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, strong jolts, flammable
gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
‑ is visibly damaged,
‑ is no longer working properly,
‑ has been stored for extended periods in poor ambient conditions or
‑ has been subjected to any serious transport‑related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Never point a garden hose at the product.
• The product may not be mounted in or under water.
• For installations in industrial facilities, follow the accident prevention
regulations for electrical systems and equipment of the government
safety organization or the corresponding authority for your country.
• Correct polarity must be observed while inserting the (rechargeable)
batteries.
• (Rechargeable) batteries should be removed from the device if it is not
used for a long period of time to avoid damage through leaking. Leaking
or damaged (rechargeable) batteries might cause acid burns when in
contact with skin, therefore use suitable protective gloves to handle
corrupted (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of children. Do not
leave (rechargeable) batteries lying around, as there is risk, that children
or pets swallow them.
• All (rechargeable) batteries should be replaced at the same time.
Mixing old and new (rechargeable) batteries in the device can lead to
(rechargeable) battery leakage and device damage.
• (Rechargeable) batteries must not be dismantled, short‑circuited or
thrown into fire. Never recharge non‑rechargeable batteries. There is a
risk of explosion!
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Inserting / replacing batteries
• Open the housing by turning the front part of the housing counter‑clockwise.
• Carefully pull the battery compartment out from the housing.
• Open the battery compartment cover.
• Insert 2 AA batteries (not included) according to correct polarity. Heed correct
polarity as indicated in the battery compartment.
• Close the battery compartment.
• Slide the battery compartment back into the housing till the very end. When doing so,
the battery compartment must be aligned with both guide rails inside the housing.
• Close the housing and make sure the battery compartment locks into place properly,
in order to guarantee the weatherproof properties of the device.
Replace the batteries as soon as the red LED stops flashing or flashes just
slightly.

Installation

• Choose a suitable installation surface.
• Mark the position of the mounting holes on the mounting surface, for example using
a pencil.
• Drill the mounting holes into the surface.
When drilling or tightening screws, make sure not to damage any cables,
wires or pipes located underneath the surface.
• Attach the product to the surface. If necessary, use the screws and wall plugs
provided.
• Loosen the lock screw in order to align the housing as needed. Lock the position by
retightening the lock screw.
Lock screw