MPEM PROGRAMMER GUIDE INTRODUCTION INTRODUCTION This document is to be used as a training supple- ment to your shop manual and service school ma- terials . This document will offer you the newest and latest specifications to properly care for and use your MPEM Programmer and vehicle electri- cal system.
MPEM PROGRAMMER GUIDE GENERAL SPECIFICATIONS OF PROGRAMMER GENERAL SPECIFICATIONS OF PROGRAMMER The basic function of the programmer is to open DESCRIPTION OF DESS SYSTEM the record option of the snowmobile MPEM The DESS (Digitally Encoded Security System) is memory. a deterrent against theft. Factory programmed, This programmer version is V2.1D.
MPEM PROGRAMMER GUIDE GENERAL SPECIFICATIONS OF PROGRAMMER KEY PAD When these keys are touched the cursor will move up or down. When more than The key pad is sub-divided into 2 main areas; the 4 items are listed this will allow you to control key area and the data entry area.
Programmer is already updated with the latest software version 2.1. This software version needs to be configured depending on programmer op- tions (Sea-Doo, Ski-Doo or Sea-Doo + Ski-Doo). To configure programmer options, dealer must contact the nearest Service Representative to ob- tain an authorization number.
MPEM PROGRAMMER GUIDE PROGRAMMER PREPARATION Procedure Note new password (given by the Service Repre- sentative): _____________. Scroll to desired language by moving pointer with ê or é keys. Press any key on the programmer to move to the next screen. Press ENTER.
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE PROGRAMMING PROCEDURE VEHICLE SET-UP CHECK KEYS (MAIN MENU) (BEFORE PROGRAMMING) This option allows to check any keys for proper internal electronic components before program- Before any programming procedures the follow- ming. This option will not verify if key can start ing must be performed: engine and should always be used before pro- –...
Page 10
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE Add Keys The following chart lays out the complete procedure to program a new key. Step 1 1 . C H E C K K E Y S S A V E + Q U I T >...
Page 11
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE Delete Keys The following chart lays out the complete procedure to erase keys. NOTE: At least one tether cord must be programmed. Step 1 1 . C H E C K K E Y S S A V E + Q U I T >...
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE VEHICLE INFO (MAIN MENU) SAVE + QUIT FUNCTION The SAVE + QUIT function needs to be per- formed to ensure that information is transferred > 1 . C U S T O M E R N A M E from programmer to vehicle electronic module 2 .
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE Press ENTER or any key. VEHICLE SERIAL NUMBER (main menu è vehicle info.) The final screen to see is: This option is a read only menu. Serial Number is programmed at factory and cannot be deleted or modified.
– software application (APP): R E S E T ? • 9 and less refers to SEA-DOO software = > Y E S • 10 and more refers to SKI-DOO software A00A3BA – MPEM serial number – MPEM software version This option records hours and is resettable to the needs of a servicing dealer.
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE OTHERS (MAIN MENU) TEST PGMR (main menu others) è This option allows to test programmer for proper operation. L A N G U A G E NOTE: Programmer automatically performs the D I S P L A Y A D J . internal test operation.
Page 16
Service Rep. phone no.:_______________________ SEA-DOO Dealer V2.1 D NOTE: There is a short delay between each SKI-DOO + SEA-DOO V2.1 P screen. Do not press any key. To bypass a screen, Dealer press ENTER. Refer to phone number table at the end of this document.
Page 17
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE MAIN MENU 1. CHECK KEYS 2. PROGRAM KEY 1 . A D D K E Y S 2 . E R A S E K E Y S 3 . S A V E + Q U I T 3.
MPEM PROGRAMMER GUIDE PROGRAMMING PROCEDURE ERROR CODES A possible ERROR display message might show: E R R O R E R R O R E R R O R E R R O R E R R O R E R R O R A00A3HA This triple display does NOT require programmer replacement.
MPEM PROGRAMMER GUIDE SELF-DIAGNOSTIC SELF-DIAGNOSTIC OPERATING SELF-DIAGNOSTIC NUMBER OF BEEPS CAUSE REMEDY 2 SHORT • Everything is correct with the tether • None... engine can revolve normally. cord (good contact and correct cord). (when engine is started) 1 SHORT EVERY •...
MPEM PROGRAMMER GUIDE SERVICE REPRESENTATIVE PHONE NUMBERS SERVICE REPRESENTATIVE PHONE NUMBERS The following table lists all available Service Representative phone numbers when calling for an authori- zation number or a new password. SERVICE REPRESENTATIVE COUNTRY PHONE NUMBERS UNITED STATES 1-800-366-6992 CANADA 1-800-361-9980 SOUTH AMERICA...
Need help?
Do you have a question about the Bombardier MPEM 480 1436 01 and is the answer not in the manual?
Questions and answers