Page 1
Owner's Operator And Maintenance Manual Owner's Operator and Maintenance Manual (Adjustable Seat Angle) DEALER: THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE.
Page 2
READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS AND INSTRUCTIONS, CONTACT A QUALIFIED TECHNICIAN BEFORE ATTEMPTING TO USE THIS EQUIPMENT - OTHERWISE INJURY OR DAMAGE MAY RESULT. SAVE THESE INSTRUCTIONS A-4 Part No. 1110545...
ADJUSTING TOE IN/TOE OUT ......................32 ADJUSTING THE AXLE TUBE ......................34 REPOSITIONING CAMBER INSERTS (ADJUSTING REAR WHEEL CAMBER) ..... 36 ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) ......38 ADJUSTING WHEELBASE WIDTH ....................39 REPLACING AXLE TUBE ........................40 Part No. 1110545 A-4...
Page 4
ADJUSTING THE T-ARMS ........................62 ADJUSTING T-ARM TRANSFER ASSISTS AND/OR SIDE GUARDS ........65 REPLACING THE T-ARM LOCKING LEVER ................... 66 INSTALLING THE HALF ARM SOCKET ................... 67 ADJUSTING HALF ARM HEIGHT ....................... 67 LIMITED WARRANTY ..............68 A-4 Part No. 1110545...
DO NOT OPERATE WITHOUT for proper anti-tipper THE ANTI-TIP TUBES INSTALLED. REV. 5/98 P/N 60106X144 setting. 1085379 Detent balls should extend beyond the diameter WARNING of the axle bushing for a positive lock. Keep detent balls clean. REV.10/98 1026960 A-4 Part No. 1110545...
SPECIFICATIONS INVACARE A-4 * NOTE: The seat-to-floor heights are based on pneumatic tires and pneumatic tires with flat free inserts. If wheelchair is equipped with urethane tires, subtract 1/4-inch from the measurements listed above. All heights are measured with properly inflated new tires. These heights can vary +1/4-inch due to tire wear.
(ü) to maintain the proper stability, safety and handling of the wheelchair. NOTE: Additional adjustments may be needed according to the wheelchair type. Refer to the wheelchair owner's manual for these procedures. A-4 Part No. 1110545...
Page 15
STAIRWAYS WARNING ESCALATORS? SORRY! Part No. 1110545 A-4...
Page 16
TRANSFERRING TO AND FROM OTHER SEATS WARNING CAUTION NOTE: This activity may be performed independently provided you have adequate mobility and upper body strength. A-4 Part No. 1110545...
Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair. To operate properly and safely, your wheelchair must be cared for just like any other vehicle. Routine maintenance will extend the life and efficiency of your wheelchair. SAFETY INSPECTION CHECKLIST Part No. 1110545 A-4...
Section 3 - Upholstery includes the following: Unfolding/Folding the Back Removing/Installing Standard Back Upholstery Adjustable Tension Back Upholstery Seat Upholstery Replacement WARNING UNFOLDING/FOLDING THE BACK (FIGURE 1) WARNING Back Cane Back Release Cord (Not Shown) NOTE: Back upholstery removed for clarity. A-4 Part No. 1110545...
REMOVING/INSTALLING STANDARD BACK UPHOLSTERY (FIGURE 2) WARNING REMOVING STANDARD BACK UPHOLSTERY INSTALLING STANDARD BACK UPHOLSTERY Back Upholstery Fold Fastening Strips Fastening Flap Fastening Flap Loops Back Canes Part No. 1110545 A-4...
Upholstery Cover Fastening Strap THE BACK UPHOLSTERY COVER Back Cane Mounting Hole Back Upholstery Anchor Loops Mounting Screw Back Upholstery Adjuster Straps REMOVING/INSTALLING ADJUSTABLE TENSION BACK UPHOLSTERY NOTE: To remove adjustable tension back upholstery, reverse STEPS 2-4. A-4 Part No. 1110545...
NOTE: Clean the upholstery with warm water and mild detergent to remove superficial soil. WARNING SEAT UPHOLSTERY REPLACEMENT (FIGURE 4) Phillips Screws Seat Upholstery Seat Frame NOTE: Wheelchair frame not shown for clarity. Part No. 1110545 A-4...
Determining Toe in/Toe out Adjusting Toe in/Toe out Adjusting the Axle Tube Repositioning Camber Inserts (Adjusting Rear Wheel Camber) Adjusting Wheelbase Length (Adjusting Center of Gravity) Adjusting Wheelbase Width Replacing Axle Tube WARNING BACK ANGLE ADJUSTMENT (FIGURE 1) A-4 Part No. 1110545...
AXLE TUBE POSITIONING FOR 0°/3°, 0°/6°, 3°/6° OR 9°/12° CAMBER INSERTS (FIGURE 7) CAUTION AXLE TUBE POSITIONING FOR 0°/9°, 0°/12°, 3°/9°, 6°/9° , 3°/12° OR 6°/12° CAMBER INSERTS (FIGURE 7) WARNING CAUTION 0°, 3° or 6° Camber. 9° or 12° Camber. A-4 Part No. 1110545...
Page 33
Axle Tube - LOCKED OUT by Toe Adjustment Rings and Will NOT Rotate AXLE TUBE POSITIONING FOR 0°/9°, 0°/12°, 3°/9°, 3°/12°, 6°/9° or 6°/12° CAMBER INSERTS Axle Tube - Will Rotate DOWN Only Axle Tube - Will Rotate UP Only Part No. 1110545 A-4...
Installing the T-Arm Sockets Installing/Removing the T-Arms Adjusting the T-Arms Adjusting the T-Arm Transfer Assists and/or Side Guards Replacing the T-Arm Locking Lever Installing the Half Arm Socket Adjusting Half Arm Height WARNING INSTALLING THE T-ARM SOCKETS (FIGURE 1) A-4 Part No. 1110545...
Move the bottom clamp up one (1) of two (2) mounting positions in the side guard. Large Side Guards - Move the bottom clamp up one (1) of three (3) mounting positions in the side guard. Part No. 1110545 A-4...
Need help?
Do you have a question about the A-4 and is the answer not in the manual?
Questions and answers