Voltek 1816 Installation Instructions

COMPLETING THE INSTALLATION
1. Once the jumper and time settings has been set to the desired position,
screw the sensor back into the lid using the four screws.
2. Connect the other end of the cable to the control equipment following the
connection details on the previous page.
3. Apply power to the system. When first powered, the sensor will take
approximately 1 minute to settle down into normal operation.
4. Walk in front of the sensor and ensure the detection area is being covered
adequately. Adjust the pan and tilt of the sensor to the desired position and
use the screw on the front of the enclosure to lock in position. (Do not over-
tighten as this may prevent you from making changes in the future).
WARRANTY
This product has a 2 Year parts and labour warranty. In the unlikely event that
you encounter a problem with this product, it should be returned direct to
Voltek, or to the place of purchase.
Voltek Helpline : 01282 695500
SPECIFICATION
Operating Voltage 12Vdc Nominal
Current Consumption 33mA (standby)
40mA (alarm)
Sensor Dual element thermally stabalised
Relay type Single pole change over
Relay Contact rating 1A (24V dc), 0.5A (120V ac)
Transistor Output npn with 22K pull up and 100R in series
Transistor rating 80mA (sink only)
Alarm duration 2 sec. To 5 min. (Relay)
2 sec. minimum (transistor)
Weatherproofing IP55 (suitable for outside use)
Dimensions 80mm W x 110mm H x 115mm D
Total package weight 0.2Kg
Approvals CE Directive 93/68/EEC
EMC Directive 89/336/EEC
BS EN 50081-1, BS EN 50082-1
39c Churchill Way, Lomeshaye Ind Est., Nelson. Lancs. BB9 6RT. UK
Tel (01282) 695500 Fax (01282) 695511 International (+44 1282)
Email : sales@voltek.co.uk Website : www.voltek.co.uk
Installation Instructions
This product is a high quality PIR sensor which has suitable outputs and
controls for use with your alarm panel, CCTV equipment, radio pagers and
lighting controllers.
CONTENTS
• Autoswitch PIR Sensor
• Fixing kit containing 2 screws, 2 plastic wall plugs and a cable tie.
FEATURES
• 12V dc operating voltage.
• 18 metre(max), 90° detection range (standard lens).
• 40 metre(max), 12° detection range (long range lens).
• LED movement indicator (can be disabled).
• Normally open and normally closed relay output.
• Adjustable relay alarm time (2 sec. to 5 mins.)
• Transistor output (-ve signal in alarm).
• Selectable pulse count 1, 2, 3 or 4.
• Adjustable Time Frame 5, 10, 20 or 30 sec.
• Relay output will go into alarm on removal of power.
• Relay & transistor will go into alarm if the PIR input is disconnected.
• Tamper Switch
SITING THE PIR SENSOR
• We recommend that the sensor is mounted at a height of between 2.5 to 3
metres to obtain the best coverage pattern.
• Place the sensor so that movement is across the face of the sensor, rather
than straight towards it. A person would cross more of the detection beams
this way and therefore increase the sensors sensitivity. (see detection
patterns)
• The unit should be fixed to a rigid, vibration free, vertical surface.
• Do not locate the device in site of heater flues or air conditioning equipment
as they may cause a false alarm.
Use the detection pattern shown on the next page to help determine the best
location for the sensor.
You may wish to do a scaled plan view sketch of the property and add the
detection patterns to the sketch to ensure that all approaches to the property
have been covered.
Issue 3
1816 1816LR
,
AUTOSWITCH