Table of Contents
Advertisement
Quick Links
Brought to You by www.snapwhole.com
AIR BRAD NAILER KIT
AIR BRAD NAILER KIT
AIR BRAD NAILER KIT
AIR BRAD NAILER KIT
AIR BRAD NAILER KIT
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
Copyright
2002, 2004 by Harbor Freight Tools
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
18 GAUGE
18 GAUGE
18 GAUGE
18 GAUGE
18 GAUGE
MODELS
TO PREVENT SERIOUS INJURY,
40050
40051
®
. All rights reserved. No
REV 08/04
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools CENTRAL PNEUMATIC 40050
Summary of Contents for Harbor Freight Tools CENTRAL PNEUMATIC 40050
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.
-
Page 2: Specifications
Brought to You by www.snapwhole.com Specifications Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. - Page 3 Brought to You by www.snapwhole.com Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. Use eye and ear protection. Always wear ANSI approved impact safety goggles and appropriate hearing protection. Wear a full face shield if you are producing metal filings or wood chips.
- Page 4 Brought to You by www.snapwhole.com heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your air compressor’s manual for the appropriate size cord. It is also possible that the use of an extension cord may cause your circuit breaker to trip or your panel fuse to break.
-
Page 5: Operation
Unpacking When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Oil Dropper... - Page 6 Brought to You by www.snapwhole.com Operation (continued) The Nailer should not fire if the nose is not depressed against the workpiece. Check that the Trigger (37) and the Safety (42) or “nose” move freely, without sticking - see the illustration at the bottom of this page. Connect the air supply to the tool at the 1/4”...
-
Page 7: Clearing Jams
Brought to You by www.snapwhole.com Operation (continued) Operating the Nailer Attach the Nailer to the air supply at the 1/4” NPT Air Plug (72). Start your compressor and check the pressure making sure it is set at the recommended 55-95 PSI and not to go over the maximum 95 PSI. -
Page 8: Maintenance
Brought to You by www.snapwhole.com Clearing Jams (continued) Lightly oil the Driver (18). Replace the Driver Guide FIGURE 3 Cover (45) and latch the Quick Release Spring (48) under both hooks, making sure it is securely in place and the Quick Release Lever (42) is pressed down - see Figure 3 . -
Page 9: Parts List
Brought to You by www.snapwhole.com Parts List l l o n i l l i a l i a SKU 40050 & 40051 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Assembly Drawing
Brought to You by www.snapwhole.com Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
Need help?
Do you have a question about the CENTRAL PNEUMATIC 40050 and is the answer not in the manual?
Questions and answers