VAPEX TECH Smart Efficharger Owner's Manual

Model NO.: VP24W
Smart Efficharger
Smart & Super-Fast Charger for
4~10 Cells Battery Packs
This Charger is designed to charge Nickel-Metal
Hydride or Nickel Cadmium 4~10 Cells battery
packs with Standard Tamiya Male Connector.
This is a Super-Fast & Smart Charger, which can
distinguish 4~10 cells pack by MPU inside
automatically and cut-off the charging accordingly.
It is easy to use. Manual-adjustment is not
needed.
By using different adaptors, this charger can be
used to charge battery packs with Futaba Female
connector, JR Female connector, Tamiya Small
Male connector, Micro Female connector etc.
SAVE THESE INSTRUCTIONS
Input Rated Voltage & Line Frequency:
100~240VAC 50Hz~60Hz
Rated Voltage: DC18.0V+-5%
Rated Current: DC1350mA
Rated Cells Pack: 4~10 Cells
No Load Voltage: DC20V Max
Trickle Current: 60mA Max
Short Circuit & Reverse Polarity
Protection included
Features:
Recharges 4~10 pieces cells battery packs
Ni-MH/Ni-Cd batteries with Standard Tamiya
Male connector.
Microprocessor-control System (For protection
and safety).
Batteries life is well protected by –dV detection
and timer protection.
4LEDs display for Rapid charge/trickle charge
Red LEDs Flash- rapid charge
1 LED Steady: 30%
2 LEDs Steady: 50%
3 LEDs Steady: 70%
4 LEDs Steady: 90%
Green LED- Fully Charged & trickle charge
Flash Red and Green LED- Short or Reverse
polarity or Wrong Battery
Safety features :

-dV cut-off function
OPERATION INSTRUCTIONS : -
1- Connecting 1 pack of 4~10 cells pack with
Tamiya Male connector to the Female
connector of the charger.
2- Make correct contact of the Female and
4~10 Cells Battery Pack Super-Fast Smart Charger's Owner's Manual
Male connectors.
3- Plug charger into mains socket.
4- The status 4 LEDs will flash first to check if
the charger good to use, then the 4 LEDs
will be flash red from left to right when the
batteries are receiving charge. The LED
steady Red light shows the charging status
of the battery
5- After charge is completed, the status LED
will change green to indicate that the
charge is completed and batteries are
ready for use. Once the status LED is
Green, the charge switches to trickle mode
to keep the batteries at full.
6- Unplug the charger and remove the batteries
from the charger when not in use.
Mechanical Specification:
1. Plastic Case: 60×42×20mm
2. Output DC Cord: 24AGW×1500mm×2C
Environmental
Operating temperature: 0~35℃
Short Circuit Protection: 20mA
Weight: W.T. 453g for EU adaptor
W.T. 460g for UK adaptor
Package: white box
Dimension: 82mm(L)×60mm(W)×100mm(H)
.
Charging table
Battery Pack Output
Current
4.8V~6.0V 3A
7.2V~9.6V 2A
10.8V~12.0V 1.5A
Charging time for 4.8V~6.0V NiMH Packs
Size Vapex Battery
Type
950mAh In950AAA
1600mAh VP1600AFP,
VP1600AF
2000mAh VP2000AFP,
VP2000AAFP,
VP2000SC
2200mAh VP2200SCS
2500mAh VP2500SC,
in2500AA
2600mAh VP2600AA
3300mAh VP3300SC
3700mAh VP3700SC
4300mAh VP4300SC
4600mAh VP4600SC
5000mAh VP5000SC
5300mAh VP5300SC
Charging time for 7.2V~9.6V NiMH Packs
Size Vapex Battery
Type
950mAh In950AAA
1600mAh VP1600AFP,
VP1600AF
2000mAh VP2000AFP,
VP2000AAFP,
VP2000SC
2200mAh VP2200SCS
2500mAh VP2500SC,
Input
18V/1.35A
Charging Time
30mins
50mins
1.1hrs
1.3hrs
1.5hrs
1.6hrs
2hrs
2.2hrs
2.4hrs
2.5hrs
2.8hrs
3hrs
Charging Time
35mins
1hr
1.3hrs
1.6hrs
1.8hrs