Advertisement
2. INTRODUCTION aND SPECIFICaTIONS
robust, composite housing, carefully balanced and fully guarded blade drum provide quiet and safe operation. Housing design provides three
outlet positions from horizontal to vertical, allowing precise direction of airflow for cooling or drying. Handle incorporates cable stowage.
suitable for indoor and outdoor use in industrial, commercial, agricultural and automotive workshops.
Model No: . . . . . . . . . . . . . . . . . . . . aDB300 . . . . . . . . . . . . . aDB3000
Maximum airflow:. . . . . . . . . . . . 10mtr³/min . . . . . . . . . . . . 81mtr³/min
Speeds: . . . . . . . . . . . . . . . . . . . . . . 1275rpm . . . . . .940/1210/1370rpm
Supply: . . . . . . . . . . . . . . . . . . . . 230V 50Hz . . . . . . . . . . . . 230V 50Hz
Motor Power: . . . . . . . . . . . . . . . . . . . . 96W . . . . . . . . . . . . . . . 1130W
Current: . . . . . . . . . . . . . . . . . . . . . . . . . 0.5a . . . . . . . . . . . . . . . . . 5.0a
Length/Width/Height: . . . . . 300/270/330mm . . . . . . . . 518/492/530mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . .3.7kg . . . . . . . . . . . . . . . 10.2kg
3.
OPERaTION
WaRNING! Ensure you read, understand and apply safety instructions before using the blower.
3.1.
Lift the blower by the handle on the main body and manoeuvre it into desired position. use in any of the 3 positions illustrated below. Ensure that
there isn't anything in front of the blower that may be disturbed when the blower is switched on.
3.2.
check that the switch situated in the recess in the rear grille of the blower is set to "0"/off. uncoil the power lead from its stowage
position and plug into the mains power supply. Ensure that the power lead is not stretched or positioned in such a way as to cause a hazard.
3.3.
turn the blower on by switching to "I"/on. If a greater air flow is required, turn the switch to the "II" or "III" setting (ADB3000 only).
3.4.
When finished using the blower, ensure the switch is set to the "0"/off position and disconnect it from the mains power.
3.5.
rewind the lead around the lugs on the carrying handle.
3.6.
When not in use, place the blower in it's original box or otherwise protect it from dust, and store in a safe, dry, childproof location.
4.
MaINTENaNCE
WaRNING! Ensure the blower is disconnected from the mains power supply before attempting any of the following.
4.1.
use a soft, slightly dampened cloth to clean the body of the blower. Do not splash with water and never allow water to drip onto the motor
housing. Do not use solvents or other chemicals to clean the blower.
4.2.
If it becomes necessary to clean the blades or the inside of the body, remove the rear grille (the opposite side to the motor) by undoing the
retaining screws. Wipe with a slightly damp cloth only. re-fit the grille and fix in place using the retaining screws.
4.3.
should the motor, speed control box or the power lead require service or maintenance, contact your local service agent.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging
When the product is no longer required, it must be disposed of in an environmentally protective way.
Environmental Protection.
should be sorted, taken to a recycle centre and disposed of in a manner which is
compatible with the environment.
Original Language Version
ADB300 & ADB3000
Issue: 2 - 15/03/10
Advertisement
