Download Print this page
Sealey ADB300 Quick Start Manual

Sealey ADB300 Quick Start Manual

Air dryer/blower 356cfm/2860cfm

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
DO NOT cover Indoor use only
instruction
manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
2. INTRODUCTION
Robust, composite housing, carefully balanced with fully guarded blade drum providing quiet and safe operation. Housing design provides three
outlet positions from horizontal to vertical, allowing precise direction of airflow for cooling or drying. Handle incorporates cable storage. Suitable
for use in industrial, commercial, agricultural and automotive workshops.
3. SPECIFICATION
Model No: ..................................................ADB300/ADB3000
Current: ......................................................................0.5A/5A
Maximum Airflow: ..... 10m³/min(356cfm)/ 81m³/min(2860cfm)
Power: .................................................................96W/1130W
Speed(s): ................................. 1275rpm/ 940/1210/1370rpm
Supply: ...........................................................................230V
4. OPERATION
WARNING! Ensure you read, understand and apply safety instructions before using the blower.
Lift the blower by the handle on the main body and manoeuvre it into desired position. Use in any of the 3 positions illustrated overleaf. Ensure
that there isn't anything in front of the blower that may be disturbed when the blower is switched on.
4.1.
Check that the switch situated in the recess in the rear grille of the blower is set to "0"/OFF. Uncoil the power lead from its stowage
4.2.
position and plug into the mains power supply. Ensure that the power lead is not stretched or positioned in such a way as to cause a
hazard.
4.3.
Turn the blower on by switching to "I"/ON. If a greater air flow is required, turn the switch to the "II" or "III" setting (ADB3000 only).
4.4.
When finished using the blower, ensure the switch is set to the "0"/OFF position and disconnect it from the mains power.
4.5.
Rewind the lead around the lugs on the carrying handle.
4.6.
When not in use, place the blower in its original box or otherwise protect it from dust, and store in a safe, dry, childproof location.
© Jack Sealey Limited
AIR DRYER/BLOWER 356CFM,
AIR DRYER/BLOWER 2860CFM
ADB300, ADB3000
MODEL NO'S:
Original Language Version
Recommended fuse rating:
ADB300: 5 AMP
ADB3000: 13AMP
ADB300, ADB3000 Issue:4 (HF) 02/09/21

Advertisement

loading

Summary of Contents for Sealey ADB300

  • Page 1 ADB300, ADB3000 MODEL NO’S: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...

This manual is also suitable for:

Adb3000