Advertisement
4.4.8.
The wrench is fitted with self-protection circuitry.
If, when the trigger is pressed, the LED flashes 5 times, an overheat has been detected. Allow the unit to cool before further use.
The LED flashing 7 times denotes an over-current fault. In this event, the unit should be returned to either a Sealey stockist or service
agent.
4.4.9.
When the wrench is not in use, lock the trigger off by placing the forward/reverse switch in the middle position.
5. maintenance
5.1.
cleaning
Keep the outer case of the wrench clean. do not wash with water or use solvents or abrasives. use a damp cloth.
5.2.
storage
When not in use, store in a cool, dry, secure location not accessible to children.
warninG! – risk of hand arm vibration injury.
‰
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
this tool is to be operated in accordance with these instructions.
measured vibration emission value (a):
uncertainty value (k):
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool. NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
the state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be
modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and
dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the
correct use and maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on
the HSC website. www.hse.gov.uk - Hand-Arm Vibration at Work.
parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
battery removal
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered wih Valpak's
registered compliance scheme. Jack Sealey Ltd's Batteries Producer Registration Number (BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
important: no liability is accepted for incorrect use of this product.
warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
. . . . . . . . . .
15.3 m/s²
. . . . . . . . . . . . . . . . . . . . . . . . . .
sole uK distributor, sealey Group.
Kempson Way, Suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7AR
Original Language Version
1.5 m/s²
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
cP3005.V2 | Issue 3 08/03/17
Advertisement
