Advertisement
Installation & Mounting:
Permanent Mounting: Select the desired location on a flat surface for the
strobe beacon to be mounted. The visibility of the strobe flash and ease
of wiring access should be taken into consideration in the selection of the
mounting location. Using the base gasket as a template, mark the three
mounting hole locations (see Figure 1). Drill the holes using the correct
drill size to match the selected hardware. A fourth hole may be drilled for
wire access as shown in Figure 1, or the wires may be routed through the
slot in the base for external access. Connect the power wires as shown in
the wiring section (see Figure 3).
Caution:
When drilling into any vehicle surface, make
sure the area is free from any electrical wires, fuel lines,
vehicle upholstery, etc. that could be damaged
MOUNTING
SURFACE
Pipe Mounting: The 6500 series base comes with 1" NPT threads for pipe
mounting.
Temporary Mounting, Vacuum-Magnet Mount: The Vacuum-Magnet
Mount feature includes a suction cup on the bottom of the beacon, with
a magnet inside of the suction cup, for a secure, temporary mount. The
beacon should be placed in the center of the roof where the least amount
of curvature occurs. Before installing, make sure the mounting surface is
clean and there is no debris on the bottom of the beacon or on the roof of
the vehicle, which could reduce the holding power of the suction cup and
magnet. Place and remove the beacon without sliding to avoid scratching
the paint on the vehicle. After placement, the beacon should adhere firmly
to the surface. If the unit slides or moves easily, a proper installation has
not been obtained. To release the vacuum, lift the tab to release the airlock
(see Figure 2). To protect the Vacuum-Magnet Mount assembly, return
beacon to the box when not in use. Do not attempt to attach the beacon
to an ice-covered surface.
920-6500-00 Rev. D
EXTERIOR MOUNTING
HOLE LOCATION
IF DESIRED DRILL
HOLE IN CENTER FOR
WIRE ACCESS
UNDERNEATH BEACON
BASE GASKET
INTERIOR MOUNTING
HOLE LOCATION
Figure 1
PULL/ROLL TAB
UPWARD TO RELEASE
VACUUM
Figure 2
WARNING!
!
Maximum recommended vehicle speed for safe operation
using the Vacuum Mount model is 65 mph (104 km/h), when fitted
to the center of a vehicle roof of steel construction. Higher speeds
could cause the mount to fail, resulting in the beacon flying off of the
vehicle, which could cause damage to other vehicles, and injury or
death to the passengers. The vacuum-magnet mount is not intended
as a permanent mounting for the beacon. The vacuum-magnet
mount unit must be mounted on a flat smooth magnetic surface (i.e.
no fiberglass, ribbed style roofs, etc.). Ensure that the magnet is
kept clean.
Wiring Instructions:
The wiring for the strobe is as shown in Figure 3 below. All wiring should be
a minimum of 18AWG. The positive line must have a 10 amp fuse. A switch
may be used to control the on/off function. Note: Power must be shut off
when changing flash modes.
Important! This unit is a safety device, and it must be
connected to its own separate, fused power point to assure
its continued operation should any other electrical
accessory fail.
FUSE (10 AMP)
(USER SUPPLIED)
GROUND
Maintenance & Troubleshooting:
Most strobe failures can be traced to wiring or battery problems. Check all
wiring and connections to insure the correct voltage is reaching the strobe
light. If the strobe operates erratically or stops completely, and the wiring
is not at fault, the flashtube is probably worn. To replace it, remove the
lens, and remove the flashtube by squeezing on the tabs on the side of the
tube holder and pulling off. WARNING! The strobe power supply is a high
voltage device. Wait 5 minutes after turning off power before removing lens
for access to internal parts. Plug in the new tube assembly. See Figure 4.
Note: The connector is keyed to ensure proper orientation. Do not force. If
trouble continues, return product to your local dealer for warranty replace-
ment, or call ECCO Customer Service for assistance (800) 635-5900.
RED
SWITCH
(USER SUPPLIED)
WHITE
N/C = DOUBLE FLASH
GROUNDED = QUAD FLASH
GROUND
Figure 3
Figure 4
BLACK
Page 2 of 3
Advertisement
