Content Enable/Disable Configuration barcode ........................4 Version No ................................4 Factory Default Settings ............................5 Product User Configuration ............................. 5 Data Interface ................................6 USB Keyboard Layout .............................. 7 Control Character Escaping ..........................7 Control Character Output ..........................7 CR/LF Character Processing(USB Keyboard) ....................8 USB Keyboard Transfer Speed .........................
Page 3
Output Options ............................33 Edit................................. 34 AIM ID ................................34 Barcode Prefix and Suffix Order Selection .................... 35 Prefix..............................35 Suffix ..............................35 Inverse Color Barcode Selection..........................36 Barcode Type Selection ............................36 Enable/Disable All Barcodes .......................... 36 Enable/Disable All 1D barcodes ........................37 Enable/Disable All 2D barcodes ........................
Page 4
UPC/EAN/JAN Add on code ........................... 55 EAN13Convert to ISBN........................... 56 EAN13Convert to ISSN ........................... 57 GS1 DataBar(RSS14) ..........................57 GS1 DataBar Limited ............................58 GS1 DataBar Expanded ..........................58 PDF417 ................................59 Micro PDF417 ..............................59 QR Code ................................. 60 QR Code URL Link ..........................
Connection Method Put scanner connect the dedicated joint, on the other side plug into PC port. If the barcode configuration was turned off, please turn on the barcode configuration . Enable/Disable Configuration barcode Scanner can set up when enabled barcode function.In contrast, the scanner can’t set up if disabled.
Factory Default Settings Scanning the below barcode can restore the scanner the factory default. Restore Factory Default Configuration Product User Configuration Scanning the below barcode can save current parameters as user ’s configuration. Save Scanning the below barcode can restore for saved user ’s configuration. Restore User Configuration...
Data Interface This scanner support USB-KBW, RS232, USB Virtual Com. Scanning the below barcode is USB-KBW mode. USB-KBW (Default) Scanning the below barcode is RS 232 mode. RS232 Scanning the below barcode is USB Virtual Com mode(driver is needed). USB Virtual Com...
USB Keyboard Transfer Speed Used for set up scanning speed under USB keyboard mode. If PC in a lower function,please choose low scanning speed to make sure its accuracy. Low(Default) Middle High Custom Sending Speed(2ms~50ms)...
Virtual Keyboard Mode 1: Do not support output the characters between 0x20 to 0xFF by using the virtual keyboard, under the current keyboard layout. The characters between 0x00~0x1F are output according to the definition of control characters (Refer to Appendix) Model 2: Support output the characters between 0x20 to 0xFF by using the virtual keyboard.
Selection Of Host Operating System In Virtual Keyboard Mode WINDOWS(Default) MAC OS LINUX Barcode Encoding Configuration In a normal situation , the barcode encoding was identified accurately. Please use manual to set up if encountered peculiar characters, that make sure output barcode content correctly.
Output Encoding Format To output correctly in the specified encoding format. For example: It’s GBK code when output in the Notepad /Excel; It’s UNICODE when output in the Word. When output is English/Latin-1 encode format, the output mode will affected by the function switch of virtual keyboard.
Page 20
To ensure the correct output of the invoice content, when switch on the invoice code function, please configure the Chinese character output mode to GBK code (Notepad/Excel), and at the same time switch off like Code ID, User-defined prefix/suffix, and starting character to change original barcode content function .
8 Bit,1 Stop Bit, Odd Parity 8 Bit,2 stop Bit, No Parity 8 Bit,2 Stop Bit, Even Parity 8 Bit,2 Stop Bit, Odd Parity GS Control Character Replacement Do Not Replace(Default)...
Page 25
When output character is “Ç”, please first to scan” Virtual keyboard (Mode one or Mode two or Mode three)”. Replace Ç Replace | Replace ^] Replace ] Replace <GS>...
Scan Mode Auto Sense Mode off Decoding by pulling the trigger of the scanner when auto sense mode is off. It’s default mode. Off( Default) Auto Sense Mode on The scanner can sense barcode for decoding automatically. Repeat Barcode Detection Use for decode same barcode of interval time, it will decode only one time if not exceeded set time.
Successfully Decode Prompt Duration Setting Long (Default) Short Error Warning Prompt Frequency Setting (Tone) There will be four consecutive error warning tones if data transmission fails, and a single error warning tone when the unrecognized configuration code is scanned. Low( Default) Middle High...
Edit Clear All Custom Prefix Set Custom Prefix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.) Custom Suffix Output Options Off(Default)...
Edit Clear All Custom Suffix Set Custom Suffix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.) Code ID Output Options Off(Default) Before Switch on After Switch On...
Edit Set Custom Prefix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.) Clear All Custom Prefix AIM ID Off (Default) Before Switch On After Switch On...
Inverse color barcode selection (Only 1D/DataMatrix/Aztec) Normal Color Inverse Color Both (Normal/Inverse) Barcode Type Selection Enable/Disable All barcodes Enable all barcodes will low down decoding speed. So, we suggest you switch on scanner when needed. (Default is switch on state)
Interleaved 2 of 5(ITF25) Enable Disable Interleaved 2 of 5(ITF25)Check Bit Disable Check Bit (Default) Enable Check and Not Send Check Bit Enable Check & Send Check Bit Interleaved 2 of 5(ITF25)Length Selection Random Length(6-50bit)(Default)...
Page 45
6 Bit 8 Bit 10 Bit 12 Bit 14 Bit 16 Bit...
Barcode type ID Table Code type CODE ID(Default) All codes Codabar Code128 Code32 < Code93 Code39 Code11 EAN-13 EAN-8 GS1 DataBar GS1-128 (EAN-128) 2 of 5 Interleaved 2 of 5 Matrix 2 of 5 Industry 2 of 5/IATA UPC-A UPC-E ISBN ISSN Aztec Code...
Control Character Set (USB keyboard mode) Corresponding key value (enable CODE ID) Decimal Hexadecimal Corresponding key value (disable CODE ID) reserve Ctrl+@ Insert Ctrl+A Home Ctrl+B Ctrl+C Delete Ctrl+D PageUp Ctrl+E PageDown Ctrl+F Ctrl+G Backspace Ctrl+H Ctrl+I Enter (The configuration of CRLF processing decide Ctrl+J how it express)...
Configuration of instructions and examples Example for user-defined prefix and suffix: You can edit 10 characters as prefix or suffix. (In order to make sure the prefix and suffix can output normally, please enable user-defined prefix or suffix first) Example 1.1: Set”...
Example 2.1: Set Code 128 length range is 4-12bit Step: Set ”Code 128 Minimum(0~50bit)”; Set”4”; Set “Save” Set ”Code 128 Maximum (0+-50bit)”; Set”1””2”; Set ”Save” Example 2.2: Set Interleaved 2 of 5 length is 14bit It can set up by “ITF25 14bit”, through barcode length range of Maximum /Minimum to set,too.
Page 74
Safety Please not direct aim eye when the scanner has a strong ray of light, to avoid causing any hurt or unwell.