Advertisement
Option 2: Ceiling Mounting
Washers
M3×30 Pan-head Screws
Wing Nuts
(Qty.4)
(Qty.4)
(Qty.4)
1
Remove the ceiling tile.
X4
2
Place the mounting bracket in the center of the
ceiling tile. Mark the four positions of the screw
holes and a hole for the Ethernet cable to feed
through.
Drill four 4mm holes for the screws and a 10mm
Hole for Ethernet cable
hole for the Ethernet cable.
3
Secure the mounting bracket to the ceiling tile
using four M3x30 pan-head screws, washers and
wing nuts.
4
Feed the Ethernet cable through the hole. Then set
the ceiling tile back into place.
5
Connect the Ethernet cable to the Ethernet port
and push the CAP along the direction of arrows
until it locks into place, as shown on the left. Then
adjust the cable to make the exposed part hidden
behind the CAP.
Option 3: Wall Mounting
Note: Install the CAP with the Ethernet port downward.
M3×28 Plastic Wall Anchors
M3×20 Self-tapping Screws
(Qty.4)
(Qty.4)
X4
1
If your Ethernet cable feeds through the wall, you can
position the mounting bracket to make the cable
through the fixing hole. Mark the four positions of the
screw holes and then drill four 6mm holes.
2
Insert the plastic wall anchors into the 6mm holes.
3
Secure the mounting bracket to the wall by driving
the self-tapping screws into the anchors. Make sure
that the shoulders of the mounting bracket are on
the outside.
4
Connect the Ethernet cable to the Ethernet port on
the CAP and attach the CAP to the mounting
bracket, as shown on the left.
5
Push the CAP along the direction of arrows until it
locks into place, and then adjust the cable to make
the exposed part hidden behind the CAP.
3
Power Supply
The CAP can be powered via a PSE device (such as a PoE switch) or a power adapter.
Via PoE Switch
Connect an Ethernet cable from the PoE switch to the PoE port of the CAP.
PoE Switch
Via Power Adapter
Plug one end of the provided power adapter into the POWER port of the CAP and the other
end to a standard electrical wall outlet.
Power Adapter
RESET
POWER
ETH1(PoE)
ETH2
FIT FAT
4
Software Configuration
In FIT Mode
In FIT mode, the CAP should be managed by the wireless controller. Please refer to the Wireless
Controller User Guide to learn more information about configuring and using the controller.
Note: The IP address of the wireless controller must be reachable for the CAPs in the network.
In FAT Mode
1
Launch a web broswer and enter 192.168.0.254 in the address bar.
Note: To log in to the device, the IP address of your PC should be set in the same subnet address of the
device. The IP address is 192.168.0.x ("x" is any number from 1 to 253). Subnet Mask is 255.255.255.0.
2
Create a new username and password for login, and then click OK.
3
The configuration page will be shown. For detailed configurations, please visit
http://www.tp-link.com/support to download the User Guide in the download center.
For technical support and other information, please visit
http://www.tp-link.com/support, or simply scan the QR code.
The products of TP-Link partly contain software code developed by third parties, including software code subject to
the GNU General Public License ("GPL"). As applicable, the terms of the GPL and any information on obtaining access
to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under
(http://www.tp-link.com/en/support/gpl/). T he respective programs are distributed WITHOUT ANY WARRANTY and are
subject to the copyrights of one or more authors. For details, see the GPL Code and other terms of the GPL.
RESET
POWER
ETH1(PoE)
ETH2
FIT FAT
Switch
Advertisement
