CAME Corsa Series Manual
  1. Manuals
  2. Brands
  3. CAME Manuals
  4. Door
  5. Corsa Series
  6. Manual
CAME Corsa Series Manual

CAME Corsa Series Manual

Automation system for sliding doors
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CAME
AUTOMATION SYSTEM FOR SLIDING DOORS,
CORSA
WITH MICROPROCESSOR CONTROL
for door wings weighting
75
up to
AUTOMATION
SYSTEM FOR SLIDING
kg each
Ooeumorrtal.lono
'e<nIao
M70
3.1
fCW.
07f2000
eCAME
CAJI'Cf:UI
AUTOIllA~
j119PM70]
DOORS
I

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Corsa Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for CAME Corsa Series

Summary of Contents for CAME Corsa Series

  • Page 1 Ooeumorrtal.lono 'e<nIao CORSA fCW. 07f2000 eCAME CAJI'Cf:UI CAME AUTOIllA~ j119PM70] AUTOMATION SYSTEM FOR SLIDING DOORS AUTOMATION SYSTEM FOR SLIDING DOORS, WITH MICROPROCESSOR CONTROL for door wings weighting up to kg each...
  • Page 2 ""' """'1 _ _ - M_E_C_H_A_N_I_C_A_L_A_~~J_U-_~~_M~E~N_-T_-~_-~~~~~~~~~_--= The trolleys can be used to adjust the alignment of the door wings as follows: - vertical adjustment with bolts and nuts A and B - transverse adjustment with bolts and nuts C - horizontal adjustment with bolts and nuts D and +:~~.
  • Page 3 J..,0'" MECHANICAL ADJUSTMENTS VERTICAL ADJUSTMENT R' To obtain correct vertical alignment oflhe door wings, adjust the trolleys as follows: - Loosen screws A. - Turn vertical adjustment screw B until the door wing(s) is/ are as perpendicular to the ground as possible. If the automation system is being used to power two sliding door wings, adjust this screw so that no gap is left between the...
  • Page 4 --------------------_._---_._ ~""cO<SAl M_E_C_H_A_N_I_C_A_L_A_D_JUSTMENTS .:.~~~~----- ADJUSTING THE BEL TTENSION .. --:-:.-=-=-=..:J • ____ ~i -- ~'i.:;;Z~- - - - -- If necessary, the idle pulley can be used to adjust the tension on the belt. Proceed as follows: 1) Loosen the mounting screws on the pulley.

  • Page 5: Mechanical Adjustments

    ~--_ --' 1 MECHANICAL ADJUSTMENTS ---------- ~BELT SUPPORT The belt support is used to control belt vibration. It is installed at the centre of automation systems powering two door wings whose support profile exceeds 3020 mm in length. If necessary. the support may be bent into the required shape. N.B.
  • Page 6 ELECTRICAL CABINET CONNECTION FORELECTRIC L OCK TERMINAL BOARD FOR CONNECTION CONNECTION FORFUNCTION SWITCH MA7012 MOTOR-ENCODER- BATIERY-POWER MA7041 SUPPLY 2 4V CONNECTION FOR"COMPASS" OPERATING SYSTEM C;;"'B B " JJ~~ " " B " " 7' ~ ~ '1 "Hl~ 'UnCH) " ","",0' , IlUUO\A /IAA10011...
  • Page 7 ELECTRICAL CABINET RESET The RESET key, resets the data and restarts the automation in question. -{III 1111 MA70n The APRE key, starts automation and completes an opening cycle. Attention: The function of the open key is excluded if dip switch 5 APRE (10-way module) is set to ON.

  • Page 8: Selection Functions

    (O.ttA[ SPlit' SELECTION FUNCTIONS Dip 10-way SELECTION FUNCTIONS Parameter storage (used during calibration pag. 17). Checking the charge level on the emergency (whit MA7032. see pag.18). Not used. keep the dip in position "OFF". Constant push while closing "Step-by-step" operation (see contact 2-M. pag.14). Interface with other automation system (see "installing the interface system"...

  • Page 9: Verifiche Preliminari

    STARTING UP THE SYSTEM VERIFICHE PRELIMINARI Before start-up, make sure that: The electric lock (if installed) has been manually released; The proper tension has been applied to the belt (see p. 12); The checks described on p. 13 (checking for proper assembly) have been performed; No objects are present along the path taken by the door wings as they move;...
  • Page 10 ~., c"''''l I_N_S_TA_LLA_T_'_O_N_O.F ACCESSORIES (available upon request) MA7032 - Battery-powered emergency system This emergency system opens the door in case of power failure. It includes a pair of 12V (1.2Ah) batteries as well as a circuit card that keeps the batteries charged and distributes power to the automation system. By using dip switches 9 and 10 (10-way module), the emergency system can be programmed to operate in the following ways when the power fails: Note: When functioning is interlocked (see p.
  • Page 11 MA7012 - Electric lock Electro-mechanical system for locking the door wings, with gravity-powered mechanical locking action and electric unlocking system. This device locks the doorwing(s) in the closed position (and/orin the open position) by engaging a bracket installed on one of the trolleys. By using dip switches 7 and 8 (10-way module), the electric lock can be programmed to operate as follows: 7 ON Deactivated.
  • Page 12 4l> .IIIIQ.!'t!."l (CAN •••• Clll,' ••• nU.'o. v' • ••••••••••• ' "llIllel!.'A ITAiIA UW'~ e-mail 31030 ~ CAse. 92131 (10(1 70815 N.o.xn •• J(CtMIrl Info@came.1t TREYlSO 'AJUS STUTTGAIlT .iii'i'3!lfiii. ii-' Ii",!! ASSZSTEHZATECHlCA '_(Suos.1.. IIAllA CAM(AUI0M.4IlSMOSS4 n''''''A NUMERO VERDE 'l'UNII ~.:O.

Table of Contents